Question about Exercise & Fitness

1 Answer

Vision Fitness T9600HRT treadmill - how to clear the clean treadmill message?

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 6,694 Answers

If you wish to get some details; check the site linked here. Pull up older posts.

Posted on Dec 05, 2016

Testimonial: "This doesn't say anything about that error code i am getting or how to fix it"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does error code R5232 Failed mean on Vision Fitness T9600HRT treadmill

If you wish to get some details about treadmill error codes ; check the site linked here. Pull up older posts.

Dec 04, 2016 | Vision Fitness Exercise & Fitness

1 Answer

Vision fitness premier T9550

please see the chart attached. However Tight the upper and lower connector +ribbon cable inside, and clean it. Adjust the REED swtich attached diagram, clean it, and tight very well the connector.
Merry Christmas

Dec 18, 2013 | Vision Fitness - T9550 Folding Treadmill...

1 Answer

Vision fitness premier threadmill

see the chart attached. Tigh the upper and lower connector+ribbon cable inside, and clean it. However adjust the REED swtich see the diagram attached. , tight the connector and clean it. If your system has battery, replace by new ones with the same type, and clean the contacts spring from oxide, corrosion, and dust,

Dec 18, 2013 | Vision Fitness - T9550 Folding Treadmill...

1 Answer

My t9600hrt treadmill stopps working after about 15min and then i can start it up again and same

Lube the treadmill for deck belt+roller bearing too.
This happen because the lack of maintenance schedule.
See the video, if after you fix it, the problem remain, is TIME to replace the old deck board.
God bless you

Feb 25, 2013 | Vision Fitness T9600 Deluxe Treadmill

1 Answer

Vision fitness console

1) replace the batteries by new ones, clean the contacts batteries, and tight the connector very well.
2) adjust the REED swtich, see the diagram, clean it, tight the connector very well.
3) see the block diagram.


Nov 20, 2012 | Vision Fitness Console, Electronic Board

1 Answer

Vision fitness t9600hrt

see my personal TIPS:
2) you must measure the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the block diagram how the board control almost the 90 of the treadmills.

God bless you

Jun 30, 2012 | Exercise & Fitness

1 Answer

I have a vision fitness treadmill T9250 and now the console display isn't working properly. Some of the

Dear Sir:

Please see the diagram attached from REED switch, adjust, clean, and tight the connector wires very well.

2) change the batteries by new ones, use the best.clean the contact batteries.

3) tight the ribbon cable from keypad .+ tight the connector from display board vs lower board.

4) after you fix it RUN THE sofware calibration for diagnose, troubleshooting, See my personal tips for help

sincerely. God bless you

Apr 30, 2012 | Vision Fitness T9250 Deluxe Folding...

1 Answer

Error messages error lines

Dear Sir:

Adjust the reed swtich see the diagram attached, clean, and tight the connector very well.

tight the ribbon cable from keypad, and connector for display board vs lower board.
If the problem persist you must run the software calibration for diagnose and troubleshooting.

sincerely. God bless you

Apr 26, 2012 | Vision Fitness T9500 Treadmill

1 Answer

I have a vision fitness treadmill. I turn on the treadmill and it starts at P1 and then it automatically goes through all the programs and sppeds until it gets to 10 miph. I have tried unplugging it. I...

It sound like either the function pad ( more likely the problem ) or the upper electronics have failed. You will need to call Vision Fitness customer support @ 1-800-335-4348

Jun 11, 2010 | Vision Fitness T9550 Folding Treadmill

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts


Level 2 Expert

115 Answers

Sportsmith LLC
Sportsmith LLC

Level 3 Expert

918 Answers

Tom Chichester

Level 3 Expert

45036 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides