Question about Robot Coupe Food Processors

Open Question

Robot Coupe R2N Food Processor motor doesn't start. Try to remove the screws but failed. It is too deep to reach the screws. What kind of tool do I need to remove the screws. it looks like hexa key.

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 81 Answers

SOURCE: Looking for spare parts for a Robot Coupe R301 Ultra Food Process

Robot-Coupe USA.com should be able to sell you anything needed

Posted on Jul 25, 2009

  • 1 Answer

SOURCE: I have a Robot Coupe R2 food processor that quite

It just a long shaft phillips screwdriver. The screws are located under the foot pads. They just pull out and then there are the four screws.

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Robot coupe food processor RC2800 SN: R2579592 120v 6amp has no power at all, and power supply is good


You will need to find a "small appliance repair shop" in your area, most likely the main PCB has failed, it controls the motor. Check the yellow pages.

Aug 19, 2016 | Robot Coupe Food Processors

1 Answer

How to remove and install on/off pin for robot coupe r2


Thanks so much for the advice. Any idea what size TORX is required?

Jan 08, 2012 | Robot Coupe R2Dice Ultra Food Processor

1 Answer

I have a Robot Coupe R2 food processor that quite


It just a long shaft phillips screwdriver. The screws are located under the foot pads. They just pull out and then there are the four screws.

Dec 29, 2009 | Robot Coupe R2U Ultra Food Processor

1 Answer

Looking for spare parts for a Robot Coupe R301 Ultra Food Process


Robot-Coupe USA.com should be able to sell you anything needed

Jul 09, 2009 | Robot Coupe Food Processors

1 Answer

How do i seperate the housing on a robot coupe processor


There are 4 rubber shoes on the bottom of the white or gray base. Twist & pull these out. With a TORX long shank screwdriver (nothing else works, trust me) there is a screw way down in each hole. After removing the screws a gentle but firm bump should loosen the base. If you ever need to replace the motor, on the top around the drive shaft you will see three round plugs/disks, remove them by prying up with a pocket knife (works best) this will give you access to the three motor bolts.

Feb 20, 2009 | Food Processors

1 Answer

Robo coupe CL52D would not turn on


There is a reed swich (safety switch) located on the top where the lid comes down. A reed switch works with a magnet. If the magnet is missing or the reed swictch is bad, no power will be allowed to the motor. Send me your e-mail & I will look up the part # in my Robot-Coupe manual. capt_rick1912@yahoo.com

Dec 16, 2008 | Robot Coupe CL52D Food Processor

1 Answer

Makes humming sound motor will not spin


Did you replace the start capacitor or start relay first ? This is the most common problem & a hell of alot cheaper than a new motor. Did you replace the motor shaft seal (around the shaft on top of the unit ? if not you will be replacing the motor sooner than you need to because the acids from veggies eat these things up & is the main reason why the motors fail, next in line is overloading or forcing product.

Sep 15, 2008 | Robot Coupe Blixer BX6 Food Processor

1 Answer

Robot coupe r 301 ultra


Remove the base the screws are under the rubber feet,on top of the machine there are three screw caps remove these with a bradel, unscrew screws with large torx screw driver, remove spindle anti clockwise by locking out fan at base. for all Robot coupe parts go to http://www.catering-machines.com/

Jun 06, 2008 | Food Processors

1 Answer

How do I assemble the Robot Coupe R 2 Ultra


Cindy,
Send me your e-mail & I will send you back an exploded view of your Robot-Coupe. It will give all the info needed. capt_rick1912@yahoo.com

Nov 02, 2007 | Robot Coupe R2U Ultra Food Processor

Not finding what you are looking for?
Food Processors Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Robot Coupe Food Processors Experts

eyecam

Level 2 Expert

87 Answers

kakima

Level 3 Expert

102366 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Robot Coupe Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...