Question about Hoover HTC243 Top Load Washer

1 Answer

Hoover SE230 i,ve misplaced my drawing of the door switch and where the wires go, i am replacing the switch need to know where the three wires go i.e ports 1-2-3

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Green cable to number 1
white cable with silver spade fitting to number 3
double white cable to number 2

Posted on Nov 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Used washer Monday,Tuesday wont work got power to it nad cleaned filter but nothing working , Any ideas?

Ok if you have power and water to the machine, unplug for 5 min then reconnect and test from beginning. I would look at the door- close/saftey switch first then try a different setting on the selection switch. If no luck its time to call a repair man.

Nov 12, 2015 | Hoover SE230 Front Load Washer

1 Answer

Hoover SE230 - How do I remove the top cover?

Can't get the image I'm looking for but if this is like most front load washers, there is a screw in each upper corner of the back of the machine. Removing those allows you to slide the top back and then lift off.

Feb 08, 2012 | Hoover SE230 Front Load Washer

1 Answer

Hoover se 230 works perfectly except will not perform fast spin. (nothing happend when programmer dial is turned to fast cycle position

hello any spin problems can be caused by the module control board usually sits at the back of the washer may have a load of wires coming off it hope it helps


Apr 22, 2011 | Hoover SE230 Front Load Washer

1 Answer

Not spinning the water out

yoou need to check the drain pump for an can use a wet dry shop vac attach it to the end of the drain hose to remove all the water.once the water is removed.take off the hoses from the drain pump and check to see if there is something stuck in it or blocking the pump if none of these things are present you may have to replace the drain pump.good luck with your washer.let me know how this works for you.

Jan 22, 2010 | Hoover SE230 Front Load Washer

1 Answer

No power to motor

have you checked the door switch?-mike

Nov 10, 2008 | Hoover SE230 Front Load Washer

2 Answers

Hoover SE230 Programmer rotating

Hi there, my washing machine was doing the same as the one you have mentioned.
I bought a replacement timer from the website highlighted below. It has done the trick and every programme works properly now.
A competent DIY person can change one of these easily and will take about 30 minutes to do.
The new part looks slightly different but it carries the same part number.

The price £24.99 + £4.98 delivery.,46246

Mar 05, 2008 | Hoover SE230 Front Load Washer

1 Answer

Electrical problem

motor winding or wiring has shorted to chassis ground. unplug the motor connections and see if fuse still blows. if you have a multi meter use it to find the shorted conductor. there may be a black spot where its insulation has broken down and arced to ground.

Feb 03, 2008 | Hoover SE230 Front Load Washer

1 Answer

Door lock light flashing

Shame to say it but yes..

You board behind the control pannel is blown. this is caused by either a faulty door swtich or the motor.. Your model number tells me its most likely the door switch.. The control board will need replacing and the door swtich.

Getting to the board is easy only three screws near the soap draw. make sure you write which wires go where and to getto the door lock undue the door rubber if you needany further advice let me know
i have worked on more the 300 of these machines

Dec 24, 2007 | Hotpoint WMA76 Front Load Washer

1 Answer

Banging while spinning

slid the machine out away from the wall and tilt back enough to see underneath. just below the door there is a large concrete weight. chances are it is loose and needs to be tightened. if this problem has been going on for a while the bolts holding the weight on will have snaped and the drum/weight or both will need replacing . ( ex hoover engineer)

Nov 13, 2007 | Hoover SE230 Front Load Washer

Not finding what you are looking for?
Hoover HTC243 Top Load Washer Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

shaun taylor

Level 3 Expert

1525 Answers

Johnny Ramirez
Johnny Ramirez

Level 2 Expert

116 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides