Question about Panasonic SA-HE100 Receiver

1 Answer

Dvd hookup i brought a memorex dvd 2023 player and can not get it to hook up , i have 3 prongs wht yell, and red, nothing works

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 833 Answers
Re: dvd hookup

No need to play down...many guys are just as untechnical.

Players have three connections. Typically, your tv has similar inputs located on it and plug in goes color to color. Yellow is the video. Red is always the right speaker (on any system). White is the left channel. Insert a known good DVD and press play before you actually do the switchover so you can see it working in the next step. Now...set your TV to component input (it may be TV/Vid on your remote). Your TV manual should tell you how to do this. There may be more than one that button again. It will come through.

If your tv doesn't have these connections, there are similar ones on your can 'play through' by setting component input and then getting the VCR to send it on through on a TV channel. Start with the VCR tuning a channel and then switch over to component...Same deal...start the DVD first.

Posted on Dec 28, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to hook up to panasonic tv & sony dvd player

DVD output (HDMI) to HDMI input on TV will transfer both audio and video from DVD to TV. Audio output on TV to unused Input on Yamaha receiver (Aux, CD, etc.). This hookup will allow DVD and TV channels audio playback through your Yamaha receiver. Remember to test any/all new hookups or connections using minimum settings (volume, etc.), and bring up levels slowly for the initial testing.

Mar 31, 2015 | Yamaha HTR-5930 Receiver

1 Answer

Cannot get new DVD player to work on Denon AVR-2307CI Receiver


Dec 28, 2013 | Denon AVR-2307Ci Receiver

1 Answer

Hookup Blu ray player to Onkyo pre-amp for speakers

If you have audio out jacks from your tv, you would be better served hooking that up to the preamp. If you hook up the blu-ray player separately to both the tv and amp, the audio probably will not sync with the video correctly. The tv takes longer to decode the hdmi input and the audio will be ahead.

Jan 22, 2013 | Onkyo Audio & Video Receivers

2 Answers

Ouku 7" dvd player wont turn on

i have a ouku 7 inch dvd player when evere i turn on the truck the screem turns blue and it has a mute picture that binks on the left side i dont know wht it is can you help me

Sep 29, 2012 | Crown Ouku 7" Single Din Car Dvd Player...

1 Answer

I need the wireing to hookup to a tv.

Hi, it depends on the kind of TV your using...

How to Hook Up a Receiver to an HDTV

Though it utilizes the most sophisticated technology on the plant, an HDTV is extremely easy to hook up to a receiver. Home entertainment systems are designed for compatibility, whether it is a cable or satellite receiver, a DVD player or a stereo sound system.


things you'll need:

* HD television
* HD satellite or cable receiver
* DVD player
* Stereo receiver
* AV cables
* Cable connector
* HDMI cables

Examine the back of your HDTV. You will see a series of input jacks for AV cables, (typically color-coded white and red for audio and yellow for video), as well as an antenna input and one or more HDMI input jacks. There will likely be a number of them, but each one should be distinguished with a label ("video," "cable" or something similar).

Attach the cable connector from the cable or satellite receiver to the antenna input on the back of the TV.

Connect the AV cables to the DVD player, VCR, stereo receiver or whichever other component you wish to connect to the television. The cables should line up by color: place the white cable in the white input jack, the red cable in the red input jack and the yellow cable in the yellow input jack. All three cables from each component need to go into the same label input jacks. Usually, they will all line up in a vertical row.

Find the HDMI output jack on your receiver or DVD player (some receivers will not have them--they are necessary to receive a high definition signal--but can still play on the TV through the cable connector or AV cables). Attach one end of an HDMI cable to the output jack of the receiver and the other end into the input jack on the HDTV.

Turn on the TV. Access the menu with your remote, and follow any instructions it gives you. Your HDTV may require a few additional steps to complete the hookup of the receiver (though not all of them will).

Access the "input" button on your TV remote. This will allow you to switch the TV signal to one of the cable connections you have just made. For example, if you attached the HDMI cable to the first of two HDMI input jacks, the TV will flash "HDMI 1" on the screen to tell you that is where it is receiving its signal.

Tips & Warnings


Not everything that can be hooked up to an HDTV is capable of playing in high definition. The signal needs to be HD as well, which means that only HD broadcasts, HD DVDs and Blu-Ray DVDs can play in full high definition (though "upgrade" DVD players will allow normal DVDs to play at an enhanced picture). You can still hook receivers up to an HDTV, and it will still play broadcasts from them as clearly as the signal permits.

Mar 15, 2011 | Audio & Video Receivers

1 Answer


If ur using it for cd player u take the Right Out an Left Out put it in to Eq Right In an Left IN An next to it there is Right Out Left Out an to the reciver you put Right In an Left In Do that with dvd,tape....
what ever it is your trying to hook up
Right is Red
Left is White

Oct 15, 2008 | Onkyo HTR500 Receiver

1 Answer

Yamaha htr5230 hookup

Hi, Your receiver is really the same as my HTR 5240. Same back and front. basically. Go to Retrevo for manual. Shows all the hook ups. I have VCR , DVD, Tape Deck, hooked to mine but can't find the adapter so i can hook up my indoor fm antenna. All my components plug to back of receiver then there is one RCA wire running from receiver to Tv.

Sep 01, 2008 | Yamaha HTR-5230 Receiver

1 Answer


ok well rca cables does your amp have all the inputs u need video 1 2 tv cd dvd ect run casete deck play out to tape in on amp cd to cd dvd to dvd rca cables unless u use coxail digital ok now the eq only has 1 in put unless u wann run itthrow a pre amp out and in if amp has that sum dont if not pick 1 or 2 to run into eq on ther own chs then back out form eg into tape 2 monitor in ok or whatever u want so u rember what ch thats on vcr run red white to video in sterio only and s video to tv or yellow comsite vcabel ok does that help

Jan 17, 2008 | Audio & Video Receivers

1 Answer

Help with audio sound

Had the same problem - have a 3-yr old Sony DVD without hdmi - used RGB for video (hooked it up directly to tv) and optical cable for audio (connected to OPT-2 in receiver) and problem solved. the standard red/wht audio cables also worked.

Jan 10, 2008 | Denon AVR588 Receiver

Not finding what you are looking for?
Panasonic SA-HE100 Receiver Logo

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Audio & Video Receivers Experts

buck wherry

Level 1 Expert

15 Answers


Level 2 Expert

159 Answers

Brad Brown

Level 3 Expert

13362 Answers

Are you a Panasonic Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides