My industrial single needle sewing machine model T17 started but the motor get very hot and just makes humming noise but wont sew

Reliable - Single Needle Sewing Machine

reliablecorporation.com > collections > single-needle

Since 1955, Reliable machines have been the benchmark in sewing innovation and craftsmanship, including the SewQuiet servomotor, the industry leader.

Dejavu House INDUSTRIAL SEWING STANDARD NEEDLE ...

www.amazon.ca > Dejavu-House-INDUSTRIAL-Replac...

Dejavu House INDUSTRIAL SEWING STANDARD NEEDLE Replacement for ... LS2-1130 RELIABLE MSK-8800, MSK-8550M, MSK-8870M: Amazon.ca: Home ...

Reliable Single Needle, Drop Feed Sewing Machine, MSK ...

www.sewingmachinesplus.com > sewing-machine-relia...

Disclaimer: Due to the weight of the table with motor, there might be some minor marring or scratches due to shipping. This is normal when shipping industrial ...

KASINGS Industrial Needle Plate Replacement ... - Amazon.com

www.amazon.com > NewPowerGear-Industrial-Replace...

Amazon.com: KASINGS Industrial Needle Plate Replacement For MITSUBISHI LS2-190, LS2-1130 RELIABLE MSK-8800, MSK-8550M, MSK-8870M: Home ...

RELIABLE MSK-8900M INSTRUCTION MANUAL Pdf ...

www.manualslib.com > ... > MSK-8900M

Reliable single needle walking foot sewing machinee specification sheet (1 page) ... Reliable industrial blindstitch machine instruction manual (34 pages).

industrial sewing machine roller foot single-needle high shank ...

www.aliexpress.com > ... > Sewing Tools & Accessory

Reliable : MSK-8800, MSK-8550M, MSK-8870M Rex : RX8500 Singer : 31-15, 95, 96, 120U, 121C, 121D, 188K, 191D, 195K, 196K, 241, 251, 281, 366K, 400W, ... Rating: 5 · ‎1 review · ‎US$0.99 · ‎In stock

Consew220 Parts

You don't say if it is a clutch motor or a servo motor. They answer to your question is yes you can slow it down by either motor (usually a knob or switch) and by pulley. If you don't have a servo motor I would strongly urge you got contact Cobra Steve at leather sewing machine company (google it) Tell him you want one of the smart servo motors with needle position-er (needle up and down automatically)
His smart servo motors are also modified so they work very similar to home sewing machines... with graduated speed based on how hard you press the pedal.

But if you must and want to stick with a clutch motor... you might try this fellow's hack.

http://www.adafruit.com/blog/2007/11/08/hacking-an-industrial-sewing-machine-by-adjusting-the-clutch-motor/
.

Every machine is a little different, but the basics are the same. Our 7th grade Home Eco. teacher taught us the first day...
"...Start at the thread spool, thread guide, thread guide, tension, take up lever, thread guide, thread guide, needle. Learn this and you can thread any sewing machine"

she was right, As this hold true for my kenmore, juki, singer and new home machines. Same basics for industrial machines too.


Hope this helps.

NO.

before starting to sew
1.make sure the top thread & bobbin thread have a thread tail of 3 to 6 inches
2.make sure the thread tails are pulled behind the needle toward the back of the machine

then put the fabric under the presser foot to sew

when your finished with the seam, after the thread is cut from the fabric,, leave the thread tail the same as above before starting to sew again

make sure the needle is inserted correctly
check the needle clamp screw to make sure it's tight
the needle is to fine for the fabric being used
also make sure under the needle plate there is no lint
also in bobbin area
also check the tension

I have an old Consew 230B and need an operating manual can any one help me. Thank you

Hi there, please send me an email and I will send you the mechanics book for your machine.
Kindest Regards,
Richard.

[email protected]

It might be a burr on the point of the needle.