Question about Yorx DM113 Shelf System

1 Answer

How Do You take off the turntable

I bought this turntable a week or so ago, and it worked perfect for a couple of days, now it does not turn, and I think it has something to do with the belt, but I don't know how remove it. HELP

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

The mat can be removed from the platter. Under this there are often holes through wich you can see the belt and motor. The belt should have some play in it but if it pulls away easily it probably needs replacement. Sometimes there is a C shaped clip holding the platter on. If so remove it and lift the platter. Otherwise the platter just sits on a bushing around the spindle. Lightly lift the platter and if it still doesnt come off you can LIGHTLY tap the spindle while lifting the platter and that should free the platter. If it is in one piece measure it lay it flat and measure it end to end and then double that measurement. The most common is 23.6" however there are 20.7", 25", 28" and 38.8", MCM electronics has them for a few bucks each. Simply place it on the inner ledge on the bottom of the platter and stretch over the motor pully. If the speed seems off check the placement on the bottom ledge and the pully. The belt if places d too high or low can ride up the pully to the top where its wider and make the table fast.

Posted on Jul 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 yamaha kodiak 400 4x4. I bought it a couple of weeks ago and everything worked fine....I've been riding it about every day and a couple of days ago, I hopped on it and the speedometer and...


Have a look up under the dash and see if the cable drive has fallen away. If not undo the cable and try pulling out the inner. If it comes away short then its busted. See a parts house for a replacement.

Dec 29, 2014 | ATVs

1 Answer

AL-A1 turntable won t turn


take the platter & belt back off, then check to see if the motor spins, if it does the belts the wrong size or put on wrong, if it doesn't spin then you better get your butter & jam out, to put on your toast.

Jan 19, 2014 | JVC Audio Players & Recorders

1 Answer

I bought the amp a few weeks ago and it worked perfectly for a couple of days and then for some reason the controlls just froze. the tap tempo light went out and the channel control light stayed the same...


Exercise your warranty IMMEDIATELY since you just bought it! If you bought this used, you LIKELY bought someone else's problem. The problem is likely in the digital effects area... probably a bad cable contact... but if under warranty DO NOT mess with it... return it for replacement or repair.

Sep 09, 2011 | Marshall Amplification Marshall MG30FX...

1 Answer

My turntable is running slow!..and i just bought this turntable brand new a couple weeks ago...please help me.


Check the +10 / -10 slider too make sure it's not set to -10; adjust it towards +10 to the pitch / tone desired. Check the belt to make sure it is not loose. A loose belt will slip and turn the record slower than the recommended 33 or 45 RPM. Have a look at the YouTube video for correct set up if you're still having problems.

http://www.youtube.com/watch?v=zFonG5dijKU

Please rate this reply if you found it helpful. Good luck!

Jul 01, 2010 | Numark ttUSB Turntable

1 Answer

Pitch fluctuation


It is caused by the turntable not turning steadily. More than likely it is mechanical probably caused by defective belt drive. If the change in pitch is in regular interval then more than likely it is mechanical. It can be caused electrically when current or voltage fluctuates casuing the turntable to go faster or slower. Fixing this problem requires opening the unit. Check the belt it may be loose or stretched or may a debris is stucked on it.

Jun 26, 2010 | Crosley CR74 Turntable

1 Answer

Cdj 800 mk1 error code 83 02...no movement from deck at all. same discs worked perfectly 2 days ago...they work fine on my sl dz 1200


Chances are you have a defective laser mechism assembly as the error your getting is a focus and tracking error from the assembly

Sep 16, 2009 | Pioneer CDJ-800 Turntable

1 Answer

Xbox has no picture but sound works fine.


Hi, this is an internal problem, please send your console to microsoft if under warrenty.

Jun 16, 2009 | Microsoft Xbox 360 Console

2 Answers

Turntable problems


buy a better record player

Sep 27, 2006 | Emerson NR303TT CD Shelf System

Not finding what you are looking for?
Audio Players & Recorders Logo

501 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yorx Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

5113 Answers

The Knight
The Knight

Level 3 Expert

74198 Answers

Are you a Yorx Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...