Display is showing 3 dash marks. the treadmill will not come on at all. please help

https://10tv.in/telangana/congress-leader-kaushik-reddy-will-soon-join-the-trs-party-236272.html

Assuming all the cables are ok, your display is probably dead and needs repaired. But more often than not the inverter is the problem.

If you have a way to swap it with another Technogym inverter I would try that first.

https://www.youtube.com/watch?v=un9bvlwmWGY Treadmill Troubleshooting Treadmill Console Broken
Please follow the steps.
Normally the console is faulty, remember is the CPU or computer of the machine
Replace.
Blessing
[email protected]
cell+whatsApp: +50588611441

1) adjust the REED switch see the diagram attached. Clean it+ 2)test for open or faulty 3) tight the connector very well.
2) tight the upper and lower connectors very well and clean it.
3) inside from console tight the ribbon cable and clean it

God bless you

please adjust the Reed swithc,test for open or faulty. Clean it, Tight the connector very well.see the diagram attached.

2) Tight the ribbon cable for keypads inside the display board.

3) Replace the old batteries and put and new one, with the same marks, and o.k polarity, clean the contacts batteries very well witch c. cleaners.

God bless you

My motorized Treadmill is showing error E09 how can l clear the error?

Dear Sir:

1)In electronics, you must need to get the number of IC.

2)If you get some information like as the number of the Control Panel, will be more easy to find, the I.C.

3) You must shure the why the I.C. was burn? . Normally this problem can occur a) failure for some short of some component around the I.C. b) Power supply +5 or 12 Vdc or Low or Higher( Indicating that power supply is Not Good).

4) Would you please tell the exactly Model, Mark, Serial from your Treadmill? In that way I can help you more, and try to get the Schematic Diagram from your Fitness Treadmill.

Sincerely. God bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Dear Sir:

I will try to help you, please be patience and carefully, use basics tools:screwdriver, hex,allen, Dvom.

Troubleshooting: ERR2 - Motor Movement

Since the motor moves when you press speed up, focus on the optic sensor, its wire connections, and the

optic sensor wheel. If all seems well at the sensor, inspect the motor.

Optic Sensor

??? Optic sensor wheel - Make sure that the optic sensor wheel rotates securely, without wobbling, in the

middle of the optic sensor. Realign and tighten if necessary. If optic sensor wheel teeth are missing or

bent, replace the optic sensor wheel.

??? Optic sensor wires - Make sure that wires are inserted securely to the optic sensor and to the drive board.

Check wire continuity.

??? Optic sensor - Turn on unit power. Turn the motor flywheel with your hand. The optic sensor

indicator (LED10, drive board) should light. . If it does not light, and all parts above are

good, replace the optic sensor.

Motor

??? Motor arcing - Does the motor show signs of wear - irregular arcing, carbon dust?

??? Motor brushes - Do brushes show signs of irregular wear - cracks, dents, lines? Replace the

motor brushes.

??? M+ M- Wires - Make sure wires are connected properly.

Other

??? Display main IC - To ensure proper signal processing, press down on the main IC on the display

board, marked U5. .

??? Ribbon cable - Ensure that the ribbon cable is attached at the drive and display boards. Check cable
continuity.

If you need additional help, please reach me.

sincerely. God bless you.

E.CUADR
MANAGUA, NICARAGUA

Dear Sir:

I will help you inmediately.

1) Display does not illuminate
when machine is powered
on.
Insufficient power source.
Plug treadmill into a dedicated amp circuit.

2) Loose 10 pin connection at
display console or wax/lift
control board.
Check all electrical connections for proper
attachment.

3)Damaged main harness wire
connection.


4)Replace wire harness.
Faulty display console or Wax/
Lift Board.
Verify if 8VDC is present at P1 pin, 3-4 and
12VDC at P1 pin 9.
a)If yes, replace Display Console.

b) If no, replace Wax/Lift Board. See How To...
Replace Wax/Lift PCB.

Use VOM digital (Voltimeter)

Hoping that you can resolve, if you need some extra help, please reach me.

blessing.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

hai,
error4, display board maybe not fine