What is the number 1 spark plug wire for model 42a777

That's the diagram

If you look at the distributor cap from the wires side carefully, you would find either a line mark on one of the outer side of four holes (where the spark plug wires are inserted) or the numbers printed on the top of distributor cap (1,3,4,2). Fix one end of the longest high tension plug wire into number 1 hole or the one marked with a line mark on the distributor cap and the other end on spark plug number 1 (the number 1 plug is toward the pulleys and the belts side, then No 2, No 3 and No 4). While standing in front of right wheel you will see the distributor cap in front of you. The rotor moves clock wise. After you fix the 1st cord, next comes number 3 plug wire. Insert one end of the cord into the next to 1 on the right hand side and press the other side of the cord on spark plug number 3. Next to 3 is the cord number 4 and the last one is number 2.

FORD SABLE HAD TWO 3.0 ENGINES. ENGINE WITH CRANKSHAFT PULLEY FACING FRONT TOWARD RADIATOR AND GRILLE. CYLINDERS ON LEFT PASSENGER SIDE IS 1 2 3 CYLINDERS ON DRIVER SIDE THE RIGHT IS 4 5 6 GET PIECE OF PAPER WRITE NUMBER 321 AND WRITE UNDER THAT NUMBER THE NUMBER 456 STACK THEM NUMBERS ON TOP OF EACH OTHER THATS WHERE PLUGS WIRES LOCATION IS THE ROUTE THEM TO CYLINDER SPARK PLUGS NOW IF YOU HAVE THE 3.0 ENGINE TURNED SIDE WAYS.CYLINDERS FACING YOU 4 5 6 AND BACK CYLINDERS ARE 1 2 3 GET A PIECE OF PAPER WRITE NUMBER 456 THEN WRITE THIS NUMBER UNDER THAT NUMBER 321 WITH NUMBERS ON TOP OF EACH OTHER.LINED UP.THAT WILL BE YOUR SPARK PLUGS WIRES LOCATION.THEN ROUTE THEM TO THE CYLINDERS LIKE 1 TO 1 CYLINDER.

Do a complete tune up.. Spark plugs, wires, distributor cap, and rotor button... If it has coil packs that sit on top of the spark plugs.. Replace the spark plugs and cylinder number one coil

OKAY STANDING IN FRONT OF ENGINE ON LEFT SIDE CYLINDERS FACING YOU IS 1 3 5 ON RIGHT SIDE DRIVER SIDE CYLINDERS FACING YOU IS 2 4 6 LOOKING AT DISTRIBUTOR CAP NUMBER 1 SPARK PLUG ON CAP IN THE 9 OCLOCK POSITION YOUR NUMBER 5 SPARK PLUG ON DISTRIBUTOR CAP IN 6 OCLOCK POSITION .STARTING AT NUMBER 1 SPARK PLUG ON CAP COUNTING CLOCKWISE COUNTING 1 2 3 4 5 6 THATS YOUR SPARK PLUGS WIRES ON CAP TO ENGINE PLUGS. 6 PLUG WIRE ON CAP IS AT 7 OCLOCK POSITION.

The COIL PACK TOWERS are numbered : coil----3---4 pack---2---6 plug----1---5 ----------------------------------------------------------------- The engine cylinders / spark plugs are numbered : passenger side , front to rear , 1 , 2 , 3 -----drivers side , front to rear , 4 , 5 , 6 ------------------------------------------------------------------- The spark plug firing order is ( 1 -4 - 2 - 5 - 3 - 6 )

The COIL PACK TOWERS are numbered : coil----3---4 pack---2---6 plug----1---5 ----------------------------------------------------------------- The engine cylinders / spark plugs are numbered : passenger side , front to rear , 1 , 2 , 3 -----drivers side , front to rear , 4 , 5 , 6 ------------------------------------------------------------------- The spark plug firing order is ( 1 -4 - 2 - 5 - 3 - 6 )

With the 2T-C, 3T-C, and 3K-C engines the Firing Order is 1-3-4-2
The distributor rotates ->Clockwise. (The rotor actually)

Number 1 spark plug tower on the distributor cap, faces directly towards the engine. Number 2 faces the back of the engine, Number 4 faces the front of the engine, Number 3 is to the outside away from the engine.

Number 1 spark plug is at the front of the engine. 1-2-3-4

With the 4A-C engine, and other A-Series, the Firing Order is 1-3-4-2
The distributor rotates ->CounterClockwise.

Number 1 spark plug tower is towards the engine, and faces the back of the engine. Number 3 spark plug tower is away from the engine, and faces the back of the engine.
Number 2 spark plug tower is towards the engine, and faces the front.
Number 3 spark plug tower is away from the engine, and faces the front.

Hello Momtexas1:

>>Remove the Spark Plugs and Wrap the Threaded Section of the Plug with Wire, then Attach the Other End of the Wire to the Engine Block.
>>**First Make Sure the Plastic End that Snaps to the Plug is Allowing Current to the Plug. Use a Test Light or Multimeter and Check for Fire Behind this Connector (through the Large Rubber like Coil Lead to Plug) for Fire to the Plug whenever there is No Fire to the Plug.**
>>Once you are Sure the Coil Lead and Ends to the Plug are Not the Reason for No Fire to the Plug, then with the Plug Still Wired to the Engine and the Coil Lead Attached to the Plug; Remove the Coil Shut Off Wire at the Shut Off Switch.
>>Check for Fire. If No Fire, then Remove the Cut Off Wire from the Coil (removal of the blower housing required) and Check for Fire.
>>If the Spark Plugs are Firing with the Plugs Out and Properly Grounded to the Engine, then Replace the Plugs and Start the Engine.
>>Using an Insulated Plug Wire Puller, Pull the Plug Wire from 1 Cylinder. If the Engine Continuse to Run, then Replace the Plug Wire and Disconnect the Other Plug Wire. If the Engine Quits, then Replace the Other Cylinders Coil.
Send me the Model and Type or Spec Numbers Off the Engine and the Mower Model Numbers, Please. With these I can Locate the Proper Manual and Better Assist you. The Engine Model Numbers May be Stamped Into the Blower Housing (metal engine cover) Above the Spark Plug. The Mower Model Numbers are Usually Located Under the Seat on a Sticker on the Body of the Mower.
>>Thanks.

Respectfully

John

The coil have these number 1,4,3,2 these are the cylinder number and the number 1 cylinder spark is the first of the left when you are in front of the car trunk the secuency is continuos in the motor from left to right 1,2,3,4.