Question about Blitzz Technology (BWA611) Router

1 Answer

Blitzz Wireless LAN AP Router BWA601

I lost my manual to reset to default factory settings and how to get in to setup again, anyone can help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 175 Answers
Re: Blitzz Wireless LAN AP Router BWA601

Blitzz Wireless BWA601
Try downloading this utility.

Posted on Nov 19, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do I password reset

Hi Kim,

If you are unable to access the setup page of the router because you have lost or forgotten the username / password combination of the router, you will not be able to do so without setting the device to the factory condition. This means that any special settings that have been set will be lost. Before explaining the simple procedure to perform the reset - you may want to try accessing the setup page with the factory defaults:

Point or click your browser to If you haven't changed the default, this should bring you to the setup page. Otherwise, input the router address (if known). At the promt for the username and password, enter "admin" for both (no quotes) and click on the "Login" button. If you are not allowed into the router setup or do not know the setup page address folow these steps:

Note: Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and the router. You should setup the router with a wired connection first before attempting to setup any wireless connection.

Since your router has been previously configured, you should start from scratch by disconnecting all cables - except for the power cord. Then, reset the router by holding in the reset button at the back of the router for 10 seconds while it is plugged in and powered ON. Allow the router to sit undisturbed for a minute and then disconnect the power cord from the router. The router is now in the factory state and can be configured as described below:

Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to the DSL/Cable modem.

Step 2 With another network cable, connect one end of the cable to your computer's network card and connect the other end to one of the LAN (Ethernet) ports of the router.

Step 3 Power on the DSL/Cable modem and wait for the lights on the modem to settle down.

Step 4 Power on the router by connecting one end of the supplied power adapter to the power jack of the router and connecting the other end to an electrical outlet.

Step 5 Power on your computer.

Step 6 Make sure the WAN, WLAN, and the LAN port that the computer is connected to are lit. If not try the above steps again.

Follow the configuration as described in the manual linked here.

I hope this helps & good luck!

Mar 22, 2013 | Airlink AR430W Wireless Router

1 Answer

Forgotten password and username to access router

If you forget the password, you need to reset the device to the factory default settings. In that case, all configuration settings of the device are lost then you need to reconfigure the router,
To reset the device to factory default settings, follow the instructions from this link,

11_20_2011_12_11_30_am.pngHope this helps.

Nov 07, 2011 | D-Link - DSL-2640B Wireless Broadband...

2 Answers

I lost my manual and i wrote my passkey on it then i can't remember now so how can i change my passkey to connect in wi-fi router using my modem dlink 600

If the default password has been changed then -
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-

Jun 27, 2011 | D-Link DIR-600 Router

1 Answer

My Blitzz wireless router needs a password, How do I get one?

In order to get your router back to the original settings, you must push in the reset button (usually on the back of the router) for somewhere between 10 and 30 seconds depending on the router. You may need a pin or something small to push in the button, because it can be recessed. Once you have reset the router, the username and password will be changed to the defaults, admin and password, respectively. One thing you must remember is that resetting the router will change all of the router settings back to the factory settings. This means you will lose all of the changes you made since you got the router. Make sure to write down any things you've changed, so you can change them back after the reset. Also, I recommend updating to the latest firmware after the reset.

There a great article at General Router Setup.
There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

Jan 30, 2011 | Blitzz Technology (BWA611) Router

2 Answers

I forget my linksys wrt160N password. how can i open that.

In case you have forgotten the password,
You may reset router to factory setting from the reset button on the back side of the router. It may be a push botton or else use a paper pin to press the button for few seconds, the lights on the front would blink and the router would restart with factory setting. Please not that ALL SETTING WOULD BE LOST...AND YOU WOULD HAVE TO MAKE CONFIGURATIONS AND SETTING ALL OVER AGAIN

HOPE IT HELPS...Let me know if you need any further assistance

Nov 23, 2010 | Linksys WRT160N Wireless Router

1 Answer

My wirelee network is open i neep to reset password but lost instructions to do it

You can reset the Linksys back to the factory defaults.
Press the pinhole RESET button on the backof the router for 30 secs with the power on
Connect a LAN cable from the computer to the router , open a IE browser and tpye the configuration URL.
The default login and PW = admin
You can now change the default password and setup the wireless settings etc.
To secure your wireless network, please click on this link and follow my instructions :-

Jun 18, 2010 | Linksys Wireless-G Broadband Router

2 Answers

Blitzz wifi router default userID and password?

The default is admin and admin...

If that doesn't work, the reset button will clear the stored login information and reset your router to factory default.
Make sure you hold that button for about 15-20 seconds before you release it. After you did this, you can access your router again via the default IP address2.gif of

The default username and password for your Blitzz router are both "admin".

Don't forget that all your personal settings will be erased as well (wireless security2.gif, port forwarding etc.

Nov 08, 2009 | Blitzz Technology (BWA611) Router

1 Answer

Will Blitzz BWA 711 reset button clear the password/login, too?

Yes - the reset button will clear the stored login information and reset your router to factory default.
Make sure you hold that button for about 15-20 seconds before you release it. After you did this, you can access your router again via the default IP address of

The default username and password for your Blitzz BWA711 router are both "admin".

Don't forget that all your personal settings will be erased as well (wireless security, port forwarding etc.)

This is what I did after entering all that information again:
I went to each screen and took a snapshot of that window (Press ALT+PrintScreen). This screenshot I copied into a Word document and repeated these steps with all important windows. Now I have a little "manual" in case I have to reset my router again and can't remember my "fancy" settings.

If you have any more questions, just come back here and leave a comment - I'm happy to help.

Aug 28, 2009 | Blitzz Technology BWA711 (B3WL000900)...

2 Answers

Problem in setup wireless router,need default security key/phrase

If there reset the router to the factory settings:
Default Username: admin (lowercase)
Default Password: none (none, leave blank)

If this doesn't work, try pressing the reset button for 10 seconds with it powered ON. Then try it off. I can't remember which one will work.

After this is complete, username: admin and password: (nothing, blank, nada) will work.

Good Luck!

Apr 07, 2009 | Hawking 54M WIRELESS G ROUTER AP 4PORT...

2 Answers

Lost password into router need reset

Use the reset button near where the AC adapter plugs in. Hold it in for at least ten seconds. This should set it back to factory, allowing you to set another password.

Jan 25, 2009 | Belkin Wireless G Plus MIMO (F5D9230-4)...

Not finding what you are looking for?
Blitzz Technology (BWA611) Router Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blitzz Technology Routers Experts

 C. Dante
C. Dante

Level 3 Expert

623 Answers

Rick Johnson
Rick Johnson

Level 2 Expert

84 Answers

Christopher Thrash

Level 3 Expert

425 Answers

Are you a Blitzz Technology Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides