Question about Element Electronics FLX2211B 22 in. LCD TV

1 Answer

Element 26 model ELCHS 261. The tv powers up ok but

Element 26 model ELCHS 261. The powers up ok but the screen goes dark after ELEMENT logo is displayed.The picture is visible if connected to an outside monitor. The sound is good and controls are ok.It seems too that half of the screen is dark . Any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 100 Answers

Has problem on the board.the solder is loose or loose solder

Posted on Jul 18, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replaced a tcom board in a Element 55 inch tv to fix a grey screen problem. I am still getting the grey screen, should I replace the main board.

Hi Rodney,
Recently I found the main board defective for this fault in a LG42" LCD. The main board was not supplying the necessary video information to the TCon board. I hope it helps.
Good Luck.

Nov 07, 2016 | Element Televison & Video

1 Answer

It has "V1.43 Pace PR150BNM SysCode Loader" Pace. Across the top of blue screen, what's up?

Element Electronics blue screen no signal Questions ... - Fixya > Forum > Tags > blue screen no signal
Blue screen with ''component 2'' in a box shows. Then it goes black.There is also a humming coming from the tv. I have unplugged everything from the tv, and ...

element tv problem - YouTube

? 2:26
Feb 17, 2010 - Uploaded by pacman552sd1
... is a vid im attaching to my email to custamer support to try and fix my bad tv. ... LG LCD TV REPAIR - NO PICTURESCREEN FIX REVIEW ...

Dish Network - My element TV is saying "no signal". ' Directly

Jan 09, 2016 | Element Televison & Video

1 Answer

What is the part number for the blacklight inverter on the element tv ELCHS 372

Jan 10, 2013 | Televison & Video

2 Answers

Element tv screen goes out

Here is a repair service for the ELEMENT PHD42W39US:
Not sure this particular one applies to your case though...usually when sustain boards fail you lose the whole screen or brightness...or, at worst,develop some vertical lines.

Dec 06, 2012 | Element Electronics Televison & Video

1 Answer

FLX3211b when plugged in the red power light comes. Then when the TV is turned the red light turns blue and stays on. The Element logo appears for a couple seconds then the screen goes black. There is a...

the transformer for the backlight is usually what fails on the elements especially if the logo comes up briefly then the screen goes out. I would check the transformers.

Apr 04, 2012 | Element Electronics FLX-3211B 32 in. LCD...

1 Answer

Installing heating element on whirlpool dryer

The easiest way to get to the heating element would probably be to take off the front panel. Be sure to disconnect the power first as you may have to disconnect the door switch to give yourself more room. Even by doing that you don't have a full view of the element but taking out and putting in the barrel/barrel belt is a much bigger pain so you may want to try installing the heating element without pulling the entire thing apart.
As far as the wiring goes There should be two wires, one light coloured, and one dark coloured(probably white and black). The dark one usually goes to a small disk-like switch(called the 'limit switch) near the element before connecting to the actual element. The light coloured wire should go to the connector opposite the dark coloured wire.
It really doesn't matter which side of the element you connect it to as long as you don't connect them together.

Mar 23, 2010 | Dryers

Not finding what you are looking for?
Element Electronics FLX2211B 22 in. LCD TV Logo

627 people viewed this question

Ask a Question

Usually answered in minutes!

Top Element Electronics Televison & Video Experts

Cindy Wells

Level 3 Expert

5056 Answers


Level 3 Expert

485 Answers

The Knight
The Knight

Level 3 Expert

73635 Answers

Are you an Element Electronics Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides