Question about Kenwood Car Audio & Video

1 Answer

When I switched it on it only show PROTECT on the lcd display. what is wrong? and what will I do?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Disconnect the radio!!

Did you install it yourself?

Double check all the wiring - and use a continuity tester (or digital multimeter with continuity abilities) on the speaker leads.




If you hear a beep - there is a speaker wire grounded, or a speaker voicecoil blown.

To check the impedence of the speaker - set the DMM to Ohms 20x and verify the resistance is 8ohms (or very close). Anything out of this range indicates a blown voicecoil.

To verify it is not an internal amplifier problem - only wire up the Power, Switched Power, and Ground and re-try.

Thanks for using FixYa - A Very Helpful rating is appreciated for answering your FREE question.

Posted on Jul 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove protect from my cd receiver display, model HCD-EC99i?


When the protect indicator comes on, usually a power transistor has blown. The unit needs to be taken to a repair shop.

May 04, 2017 | Hardware & Accessories

1 Answer

Not switching on!


A short has transpired before the fuse. Now in protect mode. See a tech.

Mar 22, 2014 | Teac AG-980 4 Channels Receiver

1 Answer

My korg x5d doensn't show bank A anymore. Instead of A01 - pipedreams lcd screen shows blinking A01 and InitProg01???


You can try this.
STEP 1:
Set Program protect and Combi Protect to OFF.
- GLOBAL
- Using PAGE+ or PAGE-,
find untill the display show "3A-MEMORY PROTECT".
Set the parameter to OFF by using YES or NO button.

STEP 2:
Data Load.
- GLOBAL.
- Using PAGE+ or PAGE-,
find untill the display show "05A-PRESET DATA".
Change ALL to PRG (your case).
Use Left/Right Arrow button to moving cursor.
Choose "PRE-a" (your case).
Move cursor to "OK?".
Press YES when "OK" blinking for confirm.
Exit (Go to PROG button).

Feb 26, 2013 | Korg X5d

1 Answer

Compaq TFT 8020 Display Problim


have you tried going to menu and setting back to factory defaults? also, disconnect power cable and leave unplugged for 1 minute. Plug back in then see if problem is still there. Otherwise, something is wrong with the monitor that will need serviced or exchanged.

Jun 24, 2009 | Compaq TFT8020 (White) 18" LCD Monitor

1 Answer

LCD Computer monitor


This problem may occur due to wrong driver of display card or wrong display settings.
Solution:
1- Start you computer in safe mode.
2- Remove display card driver.
3- Restart you computer.
4- Install display card driver (if it does not pick automatically).

Now it should show default settings. I hope it would solve your problem.

Aug 17, 2008 | Gateway FPD2275W LCD Monitor

1 Answer

Picture disappears


My Konka LCD model KDL32AT23U Displayed a picture, then vanished, showing different colored vertical lines in horizontal blue bands.Then I could not turn it off with the remote or standby button on the side.Only with the main switch.What's wrong??
This is the same problem posted by kukish on july 26,2008

Jul 26, 2008 | Konka KDL32AT23U 32 in. LCD Television

2 Answers

PROTECT mode


I have a Sharp cd-c2900 home stereo and a "protect" word came up on the lcd?? The stereo is not working now and olnly shows a "protect" word?? Can you please tell me if there is a reset button some where?? Thanks , "Joel" My Email address>> Jovelopa22002@yahoo.com

Jul 17, 2008 | Sharp CD-C2900 Shelf System

1 Answer

Amplifier/receiver switches off systematically after a few second of use


Sounds like a bad output channel is causing it to go into protect mode. Time to see a repair tech.

May 01, 2007 | Harman Kardon HK 3480 Receiver

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4848 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...