Question about Canon i9100 InkJet Photo Printer

2 Answers

Canon i9100 flashing orange and yellow

My Canon i9100 flashes orange and green for 11 times and then holds on green for about 1 second and then starts the orange green cycle again.

Posted by on

  • markwilding6 Jul 27, 2009

    My Canon i9100 flashes orange and then green eleven (11) times before a brief pause and then it starts flashing again. Nothing on the printer moves before or after this and holding the resume button and restarting does nothing.

  • markwilding6 Jul 31, 2009

    Printer still doesn't work. I guess it needs servicing which was my initial thoughts anyway. BTW: there is no display on my i9100, just two buttons and 1 light.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,278 Answers

For general printer reset:

  1. Turn off Canon i9100 Printer
  2. Hold down Resume button and press Power button.
  3. Keep holding down Power button and let Resume button go.
  4. Press Resume button 2 times then let BOTH buttons go.
  5. Green lights will flash and then stop blinking.
  6. When green lights are solid, press the Resume button 4 times.
  7. Press the Power button and the printer should turn off, if not, press the Power button once more.
  8. Your printer should respond as normal.
If not, clean print nozzles with Windex

If still a problem, your print heads may need replacement or your printer may need to be serviced (especially if there is a Service Error message).

Hope this helps.

Posted on Jul 27, 2009

  • NinaE Jul 28, 2009

    Hi.

    If you followed steps 1 through 8 with no change, or step #5 did not occur, try cleaning the nozzles or replacing the print heads as noted. Any messages on display ?? So, if it still doesn't work, your printer would need servicing.


×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,272 Answers

Hi,

The printer has a built-in waste ink tank for the ink used during print head cleaning. Flashing light indicates that the waste ink tank is nearly full. Press the RESUME/CANCEL button to cancel the error so you can continue printing. Before the waste ink tank becomes completely full, get the waste ink tank replaced.

I hope this information allows you to resolve this issue.

If I have helped you, please help me, and rate this suggestion the highest FixYa rating. If you cannot rate this post with the highest rating, then please comment to this post and I will try to help you further.

Regards
Anand

Posted on Jul 20, 2009

  • Anand Gupta
    Anand Gupta Jul 27, 2009

    Has the issue resolved? If not, then please let me know so that we can work for a solution!



    Regards
    Anand

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I reset the EEPROM of a canon print head?


Reset Procedures for Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
  1. Turn off Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
  2. Hold down Resume button and press Power button.
  3. Keep holding down Power button and let Resume button go.
  4. Press Resume button 2 times then let BOTH buttons go.
  5. Green lights will flash and then stop blinking.
  6. When green lights are solid, press the Resume button 4 times.
  7. Press the Power button and the printer should turn off, if not, press the Power button once more.
  8. Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.

you done.

Aug 14, 2012 | Canon BubbleJet i9950 InkJet Photo Printer

1 Answer

I have a Cannon i560 printer and the light on printer flashes five times orange then flashes green, what is the problem and how can I fix it.


5 flashes indicates a faulty printhead or possibly a problem with the p/head contacts. Try removing the head which is easier if you take the cartridges out first(no tools required) and re-seat it having checked the contacts for dirt.

If that doesn't work it may be that the waste ink tank is full. Try this ...

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

May 18, 2011 | Canon BubbleJet i560 InkJet Printer

1 Answer

I have a flashing orange light and cant find the manual, I have changed the inks but its still flashing?


1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

Dec 02, 2010 | Canon Office Equipment & Supplies

1 Answer

The orange error light is flashing 5 times in between the green light.


Reset Procedures for Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
  1. Turn off Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
  2. Hold down Resume button and press Power button.
  3. Keep holding down Power button and let Resume button go.
  4. Press Resume button 2 times then let BOTH buttons go.
  5. Green lights will flash and then stop blinking.
  6. When green lights are solid, press the Resume button 4 times.
  7. Press the Power button and the printer should turn off, if not, press the Power button once more.
  8. Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Jan 27, 2010 | Canon BubbleJet i560 InkJet Printer

1 Answer

Canon I850 won't print , it has a green light for about 2 seconds then flashes a yellow light for about 6 seconds


Hi there
This is only a try it may do it but I not know,
Start with the printer OFF

1. Hold down RESUME and then hold down POWER
2. Release RESUME
3. Press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing

Select function with RESUME press POWER to execute:
presses - light color - function

Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i850)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

Jan 19, 2010 | Canon i850 InkJet Photo Printer

1 Answer

Light flashing green and yellow will not print


Hi this is only a try it may work
Start with the printer OFF

1. Hold down RESUME and then hold down POWER
2. Release RESUME
3. Press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing

Select function with RESUME press POWER to execute:
presses - light color - function

Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

Jan 14, 2010 | Canon i850 InkJet Photo Printer

1 Answer

Five flashes of orange followed by one green flesh


  1. Turn off Canon i550, i560, i850, i860, i865, i9100, i9950 Printers
  2. Hold down Resume button and press Power button.
  3. Keep holding down Power button and let Resume button go.
  4. Press Resume button 2 times then let BOTH buttons go.
  5. Green lights will flash and then stop blinking.
  6. When green lights are solid, press the Resume button 4 times.
  7. Press the Power button and the printer should turn off, if not, press the Power button once more.
  8. Your Canon i550, i560, i850, i860, i865, i9100, i9950 Printers should respond as normal.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Jan 02, 2010 | Canon BubbleJet i9950 InkJet Photo Printer

2 Answers

The printer flashes orange light five times, and green once


Probably your waste ink counter. Should be cleaned or replaced before resetting but usually you can get away with resetting once.
1. Start with printer OFF
2. Hold down RESUME and then hold down POWER
3. Release RESUME
4. press RESUME twice, then release POWER
5. let green light blink until printhead has finished moving.
6. Select functions below with RESUME, execute with POWER

0 presses - green light - Test Print (exit service for i960)
1 press - orange light - EEPROM info print
2 presses - green light - EEPROM initialise
3 presses - orange light - reset waste ink counter.

This also applies to the i550, i560, i950, i960

Sep 07, 2009 | Canon BubbleJet i560 InkJet Printer

2 Answers

FLASHING E2


hi,
CANON PIXMA MP160 All-In-One InkJet Printer
has few common problems. Such as Driver CD lost, Scanner does not work, Connection problem etc. For find all these software solution just click here....
75aba9d.jpg3f22050.jpg

http://www.canon.com/printer/prob676ijt65/solution

tonl-i-4

Jul 23, 2009 | Canon PIXMA MP160 All-In-One InkJet...

Not finding what you are looking for?
Canon i9100 InkJet Photo Printer Logo

Related Topics:

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2146 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...