Question about Mastercool 67471 Evaporative Cooler Air Conditioner

2 Answers

We bought a Bonaire cooling system at yard sale, it leaks water after it is running for awhile, plus it sprays water out the front

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 30 Answers

I take it this is a window Unit , the water is coming in the room because the Unit has to be pitched about 1/2 into the back ( outside ) or the drain line is clogged ( dirt) stopping water from flowing to condenser ( that cools the coil)
The water is condensation from warm air hitting the cold coil .

Posted on Jul 18, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

This is not an a/c unit, this is a swamp cooler. Sounds like water is getting out of the pad distributing area, need to watch it closely as it runs and see where the water is exactly coming from.

Posted on Aug 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The floor of back passenger is saturated in my holden barina 2004

Hi Water leaks can be a pain to solve. There are three possibles (1) Main cause obviously water comming in from outside ie, rain or driving through mass water on the road. (2) Water coming from cooling system entering via the heater at front. (3) air conditioner unit normally the drain leaking back into car. Because the floor slopes to the rear don't rule out the fault being at the front. If your engine has coolant in the cooling system water entering from cooling system will have a sweet smell if no smell you can normaly rule out the heater leaking however check level of coolant Make sure engine is cold. If you run your hands around the heater unit front centre inside car check for any wetness around heater and carpet. If these areas are all ok its a matter of hunting down a leak from outside. You will need a second person to spray the car with a hose whilst the other sits in the car and checks all possible areas. There are no known areas for water leaks but due to the age of the vehicle check for any cracked or shrunken rubber seals. Good luck

Aug 06, 2017 | Holden Cars & Trucks

1 Answer

How to check vacuum leak to hvac

use a spray bottle filled with water
spray a mist of water over the area where you suspect a leak while the vehicle is idling
if there is a vacuum leak the idle speed will rise and drop

Aug 17, 2016 | 2006 Pontiac G6

1 Answer

Bonaire vulcan comfort control

No it cant really be fitted as the evap system uses much larger duct and also in some cases people use a different type of duct that when running a gas heater threw it it tends to melt with the heat. Your best option would be to get new ducting that way you can size it correctly so you dont have air alance issues down the track.

May 10, 2014 | Heating & Cooling

1 Answer

Smoothie maker 600

Check to see if the jar has any cracks or if the blade assembly or collar have any cracks.
Is it possibly leaking from the tap valve?
If the blades or tap lever are cracked I would recommend replacing them, however if the jar is cracked i would just buy a new blender. These are great for smoothies but they are all discontinued and parts wont be available for much longer.

May 05, 2013 | Back to Basics 600 Smoothie Plus Work Top...

2 Answers

Vacuum leak

An old trick to finding Vacuum leaks is to use a spray bottle of water and mist seams and vacuum solenoids while the engine is running. Check the Brake booster too!

A broken EGR diaphragm can leak air into your system.

Apr 13, 2013 | 2004 Ford Escape XLT

1 Answer

What do I do if my grand marquis is running hot but I don't see a hole or anything in a hose,but its spraying water and antifreeze

What you need to do is a pressure test on the cooling system, fix leaks before going deeper. Spraying water/antifreeze would mean that the system cannot hold pressure, which is requried to keep it from boiling...

Nov 14, 2010 | 1997 Mercury Grand Marquis

1 Answer

Antifreeze leak near water pump I think Located on side of engine by serpentine belt and altenator

if your water pump has never been changed its a good bet that it is leaking. they are designed with a weep-hole that leaks to warn you that the bearing is going out. You can also verify if the bearing in the water pump is bad by grasping it at any two opposite sides and try and see if you can move it... even a little slight play indicates that it is going bad. if not the pump leaking the cleanup the engine, being careful not to spray water onto your alternator.. then get the car to normal operating temp and look for awhile at all hoses even the ones that go to the a/c heater system. another quick check is to look for crusty deposit buildups on any hoses or lines and then get the car hot and monitor. When i had a leak, it was from a small heater hose and it was a misty spray, i only found it when the engine was running.After you've corrected the problem and the engine is cool take radiator cap off and fill with 50/50 mix antifreeze. Also if you're going to change the pump out i would also change out the thermostat and replace the radiator cap if it looks a rusty and corroded. Can you rate this,,,,thanks!

Apr 29, 2010 | 2000 Oldsmobile Intrigue

1 Answer

The unit sprays for the first few seconds after I turn the unit on and then stops spraying any water or solution. I turn it off, wait a few minutes and the same thing happens. What is going on and how...

This sounds as though the pump belt is slipping. This may be caused because the pump belt has stretched slightly or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If it does then the pump should be OK but the belt may be stretched and will need replacing. If the unit does not spray after changing the belt then clean the spray nozzles at the front of the machine and make sure that water flows to the nozzles OK. You can check this by temporarily disconnecting the nozzles from the plastic pipes.

Main causes for no spray.

Bladder may be empty.
SmartMix Bottle may be empty.
The Filter may be clogged.
Tanks may not be seated properly.
Pump may have lost prime. Check all the fluid tubes / hoses for leaks or blockage (see below).
The Pump Belt may be broken.

2 front jets are blocked. This is a common problem. When the machine is standing for a while the detergent turns to a gel causing the blockage Lay the Bissell on its side then where the water comes out of the jets at the bottom of the machine unblock them using a pin to poke through the hole in the centre.

Try running hot water through the system with no detergent to empty out all the residual detergent. Keep running hot water through the system by pressing the button you press for it to spray the water do this for about 5 mins and keep swapping the water for hotter water as it starts to cool doing this 4 or 5 times might solve your problem if not get the tools out and start looking for the blockage. Do this once a month to ensure that the pipes and jets are kept clean and free of any detergent gel build up.

Oct 30, 2009 | Bissell 7901-R Clearview Proheat Plus...

1 Answer

I bought a Dazey crockpot at a yard sale. Do you

NO! water where it might end up in the heating element and the base section should not ever be submerged for cleaning, only the removable crockery.

Oct 24, 2009 | Kitchen Appliances - Others

1 Answer

Need security code for lg shine cu720 bought it at yard sale

Wow, I wish I could find cool yard sales like that. The factory LG code is 0000, unless the previous owner reset it to something else. If you can find that out no problem, if not, only your cellular service provider can reset the code for you.

Jul 08, 2009 | LG Shine CU720 Cellular Phone

Not finding what you are looking for?
Mastercool 67471 Evaporative Cooler Air Conditioner Logo

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mastercool Heating & Cooling Experts

Bill Long

Level 3 Expert

588 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers


Level 1 Expert

21 Answers

Are you a Mastercool Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides