Question about Whirlpool Cabrio WTW6600SBT Top Load Washer

1 Answer

Error code du - Whirlpool Cabrio WTW6600SBT Top Load Washer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

The F30 error code will flash when the dispenser motor cannot be driven to its proper position.



Door Unlock Error

A Door Unlock Error occurs if the door cannot be unlocked.
It will try to unlock the door 6 times before displaying the error.


Door Lock Mechanism broken.
Check Door Lock/Switch Assembly for foreign objects
Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
Door Lock/Switch Assembly Failure


If it is a cabrio:
dU flashes if the following conditions occur:
Excessive force on door lid is preventing lock bolt from retracting.
Wash media buildup is preventing lock bolt from retracting.
Machine/motor control cannot determine if door lid is in an unlocked state.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

TEST #8 Door Lid Lock
Perform the following checks if washer fails to lock (or unlock).
1. Perform Manual: Door Switch and Manual: Door Lid Lock tests.
2. Remove the console to access the machine/ motor control assembly. See Accessing & Removing the Electronic Assemblies.
3. Visually check that the P12 connector is inserted all the way into the machine/motor control. If visual check passes, go to step 4. If visual check fails, reconnect P4 and repeat step 1.
4. Check the lid lock motor winding and switches by removing P12 from the machine/ motor control and checking the
resistance values....



Component/Resistance Unlocked/Resistance Locked/Contacts Measured/Contacts Measured:


Motor Winding/35 ±5 O/35 ±5 O/P12-2/P12-3/
Lock Switch - Home/0 O/Open Circuit/P12-1/P12-4
Lock Switch - Lock/Open Circuit/0 O/P12-1/P12-7
Lock Switch - Lid/Lid Closed = 0 OLid Open = Open Circuit/Lid Closed = 0 O Lid Open = Open Circuit/P12-1/P12-5




If resistance values are good, go to step 5. If switch measurements do not match the values shown in the table for unlocked (or locked) conditions, a problem
exists in the door lid lock. Replace the door lid lock.
5. If the Manual: Door Switch or Manual: Door Lid Lock in step 1 failed, then the machine/motor control has failed: Unplug washer or disconnect power.
Replace machine/motor control assembly. Perform the Manual: Door Switch and Manual: Door Lid Lock in step 1 to verify repair.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.!!!

Posted on Sep 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Beckman DU 530 spectrophotometer has monochromator error code


He's not talking about a washing machine. It's a laboratory spectrophotometer posted in the wrong section.You'll have to send it for diagnosis and repairs. Our lab's 520 gave the same error. Estimated repair: $2-5000.

Feb 26, 2013 | Washing Machines

1 Answer

Ducati multistrada 1000 ds EFI kode 34.0 hvordan fiksa det


Hei , Anonymous for denne situasjonen jeg vil kalle min lokale forhandler eller hederlig butikk service / deleavdeling og sp?rre om eventuelle quick fix , svar , eller deler foresp?rsel . Hvis det er n?dvendig , transportere sykkelen til forhandleren eller shoppe og ha en profesjonell tekniker ta det for en pr?vetur , hvis det er i l?pende tilstand , og gi deg et skriftlig anslag for reparasjoner og svare p? eventuelle konkrete sp?rsm?l du m?tte ha om problemet. For mer informasjon om problemet og verdifulle gratis nedlastinger som du trenger kan du bes?ke nettstedene nedenfor. Lykke til og ha en fin dag. Need info error code 34 0 Signal Panel Sensor
38 0 Error code
Ducati Multistrada 1000DS 2003 2006 Repair Service Manual Download Manuals...
Ducati OEM Parts Fiche Lookup and Online Ordering
Ducati Maintenance

May 08, 2012 | 2006 Ducati Multistrada 620

1 Answer

Error code " du "


DU = Door Unlock code

Washing machine displays error code F/DU after six attempts to unlock.
-Door lock assembly failed.
-Test door lock switch
-Visually inspect wire harness connection on CCU, Door lock assembly, replace door lock assembly.

The door lock assemble on this washing machine can be replaced from either the top of the front. The door boot can be removed or the top of the washer can be removed.

Hope this helps.

Jun 22, 2011 | Washing Machines

1 Answer

Hi. My washer is coding dU then F as codes.. I cant get it to shut off and unlock the door to get cloths out. The book does not have a code for dU.. PLEASE SOMEBODY HELP ME :)


Door unlock error. The machine tried 6 times to unlock the door. Must be an item of clothing jamming the door. take the bottom panel off and reach up and grab the emergency ring, GENTLY release the door amigo. Use this GUIDE for repairs
and use your tech sheet inside that base panel for error codes and diagnostics.

Jan 24, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

F35 error


D?FAILLANCE DU CONTACTEUR MANOM?TRIQUE
If after 30 seconds the control does not detect water
entering machine, the valves will be turned off and the
error code will be displayed. OR If the control has
turned the water valves on and after 8 minutes the flow
sensor has detected 10.5 gallons of water passing
through it, but has not detected the pressure switch trip,
the valves will be turned off and the error code will flash.
Press PAUSE/CANCEL twice to clear the display.
Si apr?s 30 secondes le syst?me de commande n’a pas d?tect? l’entr?e d’eau
dans la machine, le syst?me ferme les ?lectrovannes et commande l’affichage du
code d’erreur. OU Si le syst?me a command? l’ouverture des ?lectrovannes
d’entr?e d’eau et si apr?s 8 minutes le capteur de d?bit a d?tect? le passage de
10,5 gallons d’eau, tandis qu’aucune manoeuvre du manocontacteur n’a ?t?
d?tect?e, le syst?me commande la fermeture des ?lectrovannes et l’affichage du
code d’erreur clignote.
Appuyer deux fois sur la touche PAUSE/CANCEL pour commander l’effacement de
l’affichage.
Possible Causes / Procedure
1. Unplug washer or disconnect power.
2. Check to verify that the pressure switch is
operational.
3. Replace pressure switch.

This is for an F32...there is no F35 fault code on your model according to the service manual....

Sep 11, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Du error code on a kenmore elite oasis he what does it mean and what can i di to fix the problem


Door unlock failure
Excessive force on door lid is preventing lock bolt from
retracting.
Wash media buildup is preventing lock bolt from retracting.
Machine/motor control cannot determine if door lid is in an
unlocked state. See TEST #8, page 14

Jun 11, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

DU error code


The Kenmore Oasis and Whirlpool Cabrio washers are essentially the same. Following is the Whirlpool Installation and service manual for their Cabrio washers.

The DU indicates a problem with the door Un-lock mechanism. See the section on troubleshooting2.gif and display codes.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/409753510a90c8be852571e90073421b/$FILE/8178583.pdf

Oct 13, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

WHAT IS DU?


DU is door unlock error - A Door Unlock Error occurs if the door cannot be unlocked. It will try to unlock the door 6 times before displaying the error.

Solutions -
  • Door Lock Mechanism broken.
  • Check Door Lock/Switch Assembly for foreign objects
  • Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
  • Door Lock/Switch Assembly Failure
  • May 19, 2009 | Kenmore Elite 45986 Front Load Washer

    1 Answer

    Du error code on whirlpool cabrio


    that code is for the door unlock error. is it possible that you may have tried really hard to open the units lid when it was locked? if so the door lock may have been broken. if not, then try to unplug the unit for a few minutes and try a new cycle.
    if the code comes up again then you will have to call for free service as it has a 1 year warranty for parts and labor. yes even if you broke the lid lock!!! dont worry it happens when you get something new and are not sure how it works.

    Dec 29, 2008 | Whirlpool Cabrio WTW6600SBT Top Load...

    Not finding what you are looking for?
    Whirlpool Cabrio WTW6600SBT Top Load Washer Logo

    740 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Whirlpool Washing Machines Experts

    Dan Webster
    Dan Webster

    Level 3 Expert

    8220 Answers

    Sal DeAngelo

    Level 3 Expert

    2254 Answers

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...