Question about Hotpoint Ultima WF860 Front Load Washer

3 Answers

Ultima Condensor Dryer

I have a Hotpoint Ultima Condenser Dryer model TC71, since yesterday there is no heat from the dryer. I need to know what this fault could be, and is it easy to replace.

Posted by on

  • 2 more comments 
  • Amaru Nov 19, 2007

    Washdoctor- Nice nick name. Thanks for your help i will try this out and feedback my results



    Amaru

  • Anonymous Jan 08, 2008

    no heat

  • SADANAN Feb 14, 2008

    DRYER BLOWING COLD AIR. WHERE ARE THE 2 SENSORS?

  • Anonymous Apr 05, 2008

    my dryer is blowin cold air and not getting hot can u help please nigel

×

Ad

3 Answers

Leaking water coming from under the dryer,I clean door & dryer filter before dryig plus the water container is firly slid into place.

Posted on Sep 07, 2008

Ad

Fixed it. I managed to find out the problem was, it was the two heat sensor at the back of the dryer. Once changed it was ok.
Lets see how long they last.

Posted on Nov 26, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 139 Answers

On the back of your dryer you have a heater behind the protruding panel... Either you heater element has gone, but most like the thermal cut outs have blown...these are located in the same area..they are small and round looking and are connected to them are wires either side. Anyways check the conitunity of the termal cut outs using a tester if no continuity then they are no good... hope it helps...

Posted on Nov 18, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint ultima tumble dryer


sounds like its blocked with fluff somewhere and your element could be wet take off the back and check your element and if water around it you need to compleatly clean out your filters and down where the condenser is then leave it for a day or two to compleatly dry the element

Apr 07, 2014 | Hotpoint 1701746 Ultima Tc71n Condenser...

1 Answer

Hotpoint Ultima Condenser Dryer TDC62 - No Heat


That trouble is cause by an heater that is already open- no connectivity. Also the wire connected to it.
I hope I answer your problem.

Mar 23, 2011 | Hotpoint Dryers

1 Answer

Hotpoint aquarius condenser dryer tc71 does not heat up


These washer dryers have a lot of problems. you are better off getting a seperate dryer.

Mar 07, 2010 | Dryers

1 Answer

Condenser not drying stuff properly


I am hoping your talking about a clothes dryer here. based on the model number you posted here. Does your dryer even feel warm to the touch as in any signs of internal heating? If not then here are some things to check. 1 the basics: Check the circuit breaker and make sure that both of them are in the on positon. Just trip them off and then back on again to reset them. 2. Check the power cord for any signs of a bad connection. It will show up as a dark discoloration. 3. I know you said you checked the lint filter but have you gone outside and verified that the external outlet vent is free of obstructions? If not please check it and clear any obstructions. 4. The heating element itself may be open. Ovetr time they are like light bulbs and the burn out requiring repl;acement. 5. There can be a thermostat failure causing an open circuit and no power to the heating element. 6. The motor switch also controls the heating element circuit and it is actuated when the motor is running. If the switch has failed it will prevent the heating element from being energized. 7. The least likely suspects are the timer and heat setting controls yet either of them can cause a no heat condition. You did not mention if it was a gas or electric dryer and the comments above are for an electric dryer. If you have a gas dryer then you can have 8. a bad ignitor, 9. a bad gas valve, 10. a failed gas regulator. Based on this model number CTD80 it does not cross to anything that I can find. The bottom line is your unit is probably worth the cost of getting it repaired. You may want to check your model number again please and repost it you need more information. It appears this is a UK model. I hope this was helpful. It certainly was educational here.

Jan 11, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint ultima condenser dryer TC71 is running cold


Thermostats rarely go. You could have a bad heater or even a voltage problem. Even if the dryer runs, the voltage can still be wrong, it only needs 110 volts to start the motor but must have 220 to have heat.

Apr 06, 2009 | Dryers

2 Answers

Hotpoint Ultima Condenser Dryer - where is the reservoir?


under the door, you need to take the small panel off and its there.

Mar 03, 2009 | Hotpoint Dryers

2 Answers

Drum wont move


Check the motor and the belt on the back of the unit behind the rear plate. Make sure that the belt is attached and the motor is spinning. If this helped please rate. Thank you

Feb 12, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Dryer not heating up


I hate to tell you but get ready for more problems with this drier, it has a bad track record. In some cases cleaning the condensor out and drying the unit well will allow the unit to function again. Once a month you need to empty the condenser unit, this is under the bottom panel at the front of the tumble dryer, you simply pull the panel down, undo the condenser and pull it out (it is normal for there to be some water in the tubes when you do this), you then have to flush the condenser by pouring water through it in either your sink or tub. Make sure that there is plenty of room around the drier and empty the water container often. This curcuitry of this unit it sensitive to high humidity and can cause the unit to not function properly. So with condensing dryers you have to work on keeping them clean. Let me know how it goes. Later DRRXR

Feb 02, 2009 | Hotpoint Dryers

Not finding what you are looking for?
Hotpoint Ultima WF860 Front Load Washer Logo

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1211 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

puggy666

Level 1 Expert

48 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...