Question about Toshiba DP-85F Fax

1 Answer

Toshiba e-studio50f printer error 21

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: toshiba e-studio50f

Please send the driver for e-studio50f for vista

Posted on Sep 13, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have changed my toner, and keeps on sending misfeed of paper, and now it states SERVICE CALL SC650 ???

You need to call Rich, and tell them what service call you get. They will tell you exact, what to expect. If you can solve the problem yourself, they will tell you, but most likely they will tel you you need a service technician.

Oct 20, 2014 | RICOH CORPORATION Ricoh Aficio SP C242SF -...

1 Answer

Toshiba estudio50f printer error 021

try to check gear set,sensor paper fed in main board

Feb 04, 2014 | Toshiba e-STUDIO 50F Plain Paper Laser Fax

2 Answers

Hp 500 ploter adjustment karne pra 22:10 errer cord ata he

System error 21:10 is generated when the printer has detected a fault in the Service Station. Causes of this error can include the Service Station or Carriage. Follow the steps listed below to accurately troubleshoot the issue, and replace the appropriate parts.
Part Description Designjet 500 Models - C7769B, C7770B, C7769C, C7770C Designjet 800 Models - C7779B, C7780B, C7779C, C7780C Service Station Assembly (Required) C7769-60374 C7769-60374
    NOTE:If Removal and Installation instructions are needed for reference during any repairs performed, refer to the HP Designjet 500 and 800 Series Service Manual available on the Computer Care Web site for review or download. Troubleshooting steps If any of the troubleshooting steps listed below solve the problem, attempt to verify printer functionality (instructions listed below). If functionality is verified, no additional parts should be replaced.
      NOTE: The printer's current firmware revision must be A.02.04 or higher for a new Service Station to work properly. If firmware is lower than A.02.04, download the newest available firmware before continuing with the remainder of this document.
      1. Turn the printer off, then on to verify error. If no error attempt to verify functionality.
      2. If the error appears or problems persist, continue with the remaining steps.
      3. Follow the steps directly below to unlock the Carriage from the Service Station:
        1. Highlight the Set-Up menu and press the ENTER button.
        2. Press the UP arrow and ENTER buttons simultaneously and press the ENTER button.
        3. Highlight Service Utilities and press the ENTER button.
        4. Highlight Unlock Carriage and press the ENTER button.
        5. Unplug the power cord from the printer.
      4. Manually move the Carriage assembly out from the Service Station area and check for obstructions (remove as needed).
        NOTE: If you are unable to release the Carriage by the previous process, remove the right end-cover and locate the main Service station gear (as pictured below in Figure 1) and rotate it counter clockwise approximately four revolutions. The Carriage assembly should now be free from the Service station. Figure 1: Service Station Gear
        1. If an obstruction is found and removed, plug the power cord in, turn the printer On and attempt to verify functionality.
        2. If no obstruction was found or the problem persists, continue with the remaining steps.
        3. Disconnect the power cord from the printer.
        4. Remove the right end-cover from the printer.
        5. Open the top cover and manually move the Carriage to the left so that it is not over the Service Station (refer to Step 3 for instructions).
        6. The Service Station flag should be at about a 45-degree angle as pictured below in Figure 2.
        Figure 2: Service Station flag correctly positioned
        1. If the flag is correctly positioned continue with Step 16.
        2. If the flag is not at a 45-degree angle, press in gently on the bottom of the gray and rotate the bottom of the flag to the right (toward the back of the printer) until the top of the flag clips into the tab on the Service Station. The flag should stay at about a 45-degree angle.
        3. Plug in the power cord and turn the printer on.
        4. If no error appears, attempt to verify functionality.
        5. If the error reappears continue with the remaining steps.
        6. Turn the printer off and disconnect the power cord.
        7. Replace the Service Station assembly (refer to pg. 8-52 of the HP Designjet 500 and 800 Series Service Manual).
          NOTE: The printer firmware must be upgraded to A.02.04 or higher for the new Service Station to work. The new Service Station does not have an Aerosol fan and older firmware will check for the Aerosol fan, thus causing another system error.
          1. Following replacement, turn the printer on and verify functionality as instructed below.
          Verifying printer functionality
          1. Turn the printer on.
          2. Allow initialization to complete.
          3. Load media into the printer.
          4. From the main front-panel menu, select the Ink menu and press ENTER.
          5. Select Troubleshooting and press ENTER.
          6. Follow the instructions on the Front panel.
          7. Following a successful troubleshooting print, functionality is verifie

Sep 16, 2013 | HP Hewlett Packard Designjet 500 42" Wide...

1 Answer

Toshiba 50 f showing printer error 21

toshiba 50f printer err 021 solve it my problam

Jun 01, 2011 | Toshiba e-STUDIO 50F Plain Paper Laser Fax

1 Answer

Error code 21 displayed

1. Function 7
2. Press Monitor 4 times
3. press 7
4. Press 1 to select sub code
5. press 2 you want "LBP Fuser reset"
6. then power off the machine, if the code comes pack you need a new fusing unit(the hot part), the fusing unit is what fuses the toner to the paper, if that didn't happen the toner would rub off when you touch it.

Aug 05, 2009 | Fax Machines

2 Answers

Error h4

H4 in 161, fuser low temp.; instantly solve it by simulation (c-auto-c-auto) 14; check thermistor; check fuser lamp by 5-02. it is to blink!

Jul 07, 2009 | Toshiba e-Studio DP170F Plain Paper Laser...

1 Answer

Conflict with nvidia driver

Check compatibility between your new pc configuration and toshiba's driver, you may need and update for it too.

Sep 24, 2008 | Toshiba e-STUDIO 50F Plain Paper Laser Fax

3 Answers

What is an Info Code 21?

I just had the same problem yesterday. Code 21 is not listed but in checking with a supplier it is a fuser that needs to be replaced. $175 for the part and $90 for service call.

Feb 13, 2007 | Panasonic Panafax UF-885 Plain Paper Laser...

Not finding what you are looking for?
Fax Machines Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Fax Machines Experts

Anthony Chiang
Anthony Chiang

Level 3 Expert

524 Answers

Tony Isted

Level 1 Expert

49 Answers


Level 2 Expert

93 Answers

Are you a Toshiba Fax Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides