The IR 5000 does not have a port to connect to the LAN

you need a high speed connection to the internet. depending on your tv (the ports on tv) hdmi, composite video,connect via lan or wireless(wifi), usb. with a number of devices. they all have to plug in somewhere in the tv ports
Netflix

Hi Kumar,
You can modify or change port in the printer driver to connect it through LAN cable. Please notice whether you use static or dynamic ip address. Please follow below step.

In the following step we will modify your existing USB connection. Check it out!

Step:

• Open printer driver list.
• Right click on the printer drive name (e.g Canon IR2270).
• Select Properties.
• Click Ports tab.
• Click Add Port, then select Standard TCP/IP Port.
• Click New Port.
• Click Next on add port wizard menu.
• Type IP Address (for static ip setting) or Printer Name (DHCP), then click Next (computer will search the printer).
• When the printer has been found, finish the wizard.
• Close Add Port menu.
• Now you have new port represented by IP Address or Printer Name (with checked box active) in port list .
• Click Apply.

Bingo! Now your printer ready to print via LAN. Sometimes printing right after setting this new port not always succeed. Don't be panic. Restart both of printer and the computer.
Next time you want to connect the printer via USB port so you change port back to USB. Just simply check on the check box next to USB Port in port list and click apply. You may need to restart both printer and computer too :)

Have a nice day!
Printer Clinic

connect cross lan cable to Computer and IR 3300 then
on machine there is setting button network settings check it setting
and then on computer add printer
add new printer
local printer
creat new port
next tcp/ip
add ip address of machine then next
then it demands for drivers have a disk and browse for driver path

ir your printer have lan port follow the following line
1- check ip in your printer software
2- give ip in yr pc same range
3- try ping to printer ip
4- if yr printer have html self support than simply type printer ip at yr browser check all parameter
5- add printer from control pannel with network printer option and five printer ip



vikas verma
9415563660

If I understand what you are ask???? You need to know where the ethernet cable goes in to the copier?? The conector is above the main power switch on the right side of the copier.... The print funcation is a option with a IR-5000...... Do you have a ether net PCB installed???? If you do not, you need to get a new boot rom & more ram & the ether port and lastly, you need to have your hard drive flashed to print...... Good Luck

First of all you must have a local network hub.Connect your network hub with your computer and the Ir 2800,your IR have to be equip with a network card.(If only have to connect one computer and your computer is not connected to a LAN network,you can use a cross-over cable connected directly from the computer to the IR machine.Give your computer a ip address by right clicing on the local LAN select properties and select internet protocol ver 4,and select a ip address.If your computer is already connected to a network,dont change the ip address go to command prompt tipe in ipconfig/all.This dos command will show you what the ip address is of your computer.
Example the ip address is 192.168.1.10,Select a ip address for your IR by changing the last class to any number.But you must make sure this ip is not in use,lets say you select 25.In the command prompt tipe :ping 192.168.1.25.If you get a reply,dont use the number.Select a number untill you dont get a reply and a time out response.
Now use this IP address and program it on the IR2800 under additional funcktion system setings,network settings,TCP IP settings.
Switch the machine off for a minute and switch it back on.

Now load the printer drivers of the IR and add the port you selected.
Restart the computer,

And print to your computer.

If you have any trouble along the way,just send me a note

You need to plug your comuter into one of the LAN Port and the Copier into another LAN port your Modem into toyr WAN port. Then you will need the IP of the router it should com along with the router Info and either be 192.168.000.1 or 192.168.0.1. add an ip spec range Isusualle use 192.168.000.120 this goes into your copier under network protacals in user tools. under the same area setup sub net mask 255.255.255.0 if you have already installed you Ricoh AP3800 Driver place the ip 192.168.000.120 again the 3rd set of numbers either .000 or .001 depending on your router. SO under start menu go to either printer and faxes or control panel right click on printer icon for ricoh AP3800 go to properties select the ports tab, Click add Port select Standared TCP ip Clickm the new port. Click next Add your IP adress for the Copier here. Click next Next window will have Generic network card so press NEXT and then Finished Close printer ports window and then click apply. This should get you printing

Hi,

If you are referring to the Ethernet cable, initially, it can then be presumed that your computer then has no LAN port. What would be required is purchase and installation of an add-on networking card. Although it is quite rare for most modern desktops not to have a built-in LAN port. The image below is an example of an add-on PCI LAN card

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.

You want to add a <insert brand> router to... your PC's ethernet port? If so, you just need a straight-through ethernet cable with CAT5 connectors. One end into the LAN port of the router, and the other end into the ethernet port of your PC. Done!

Now... there is a modem as well? Usually you'd have the modem (DSL, cable, whatever) plugged into the router's WAN port. The router then can share it out to all the LAN ports (of which your PC will be one of) and to any wireless clients via it's radio antenna.

So that answers that question, but if you get that done and can't configure everything, ask another seperate question please!

The best solution I use is Smart Net Monitor, which is supplied with the Ricoh disks or can be downloaded from www.ricoh-usa.com . First you need to install the lan fax driver, after that then install Smartnet Monitor.

From there click start, and then control panel, then printers and faxes, then right click on the Ricoh LAN fax driver, from there click properties, click ports, then click add a port, under available ports you will see smartnet port (highlite) and then select new port, a new box will come up and then select search, the software will then make the connection and add the port. Besure to click ok and apply and then you are connected