Axim 50/51 wont pass blue startup screen

Perform a Reset

Soft Reset
When you perform a soft reset, the device deletes any data that has not
been saved but saves any data that has been stored in memory. Try
performing a soft reset if the device does not respond when you tap the
display or press a button.
To perform a soft reset, use the stylus to press the reset button.

Hard Reset
NOTICE: When you perform a hard reset, you lose all the data stored on
your device.

Perform a hard reset if:
• You want to delete all the data stored on your device.
• You forget your password and need to clear it.
• Your device is experiencing severe operational problems and you have
already attempted a soft reset.
NOTICE: It is strongly recommended that you back up your data before you
perform a hard reset. See ActiveSync Help on your computer for more
information.
To perform a hard reset:
1 Press and hold the power button.
2 With the stylus, hold the reset button for about 2 seconds.
3 Follow the instructions on the screen.

I think your device is trying to perform the hard reset procedure. Try to soft reset it, instead, by briefly inserting the stylus pen in the reset pin (on the back of the device). If the hard reset procedure keeps coming in, I'm afraid you'll have no other option than accepting it, by pressing the left key.
Just my 2 cents... Carlos

Once you forget the Password, your only option is to perform a Hard Reset on the device and reset back to Factory defaults. You data will be lost, as this is in place to protect you in case the device has been lost or stolen. If you have backups, or sync the device with Outlook, you can run a restore or re-sync the device to populate the data back into your device.

Hard Reset:

NOTICE: When you do a hard reset, you lose all the data stored in your device
Flash memory, and any programs that you installed on your device.
Do a hard reset if:

• You want to restore the device to factory default settings.
• You forget your password and need to reset it.
• Your device is experiencing severe operational problems and you have already attempted a soft reset.
  

NOTICE: It is strongly recommended that you back up your data before you do a hard reset.

To do a hard reset:

1. Press the Power button to turn the Axim unit On.
2. Press and hold the Power button down while using the Axim stylus to press the Reset button at the same time.
3. Release the Power button and the Reset button. The To clear all data in the memory screen appears.
4. Press the Contacts button on the Axim to delete all of the data in the memory of the Axim handheld.
5. Press the Mail button on the Axim to cancel the operation without losing data.
   

try taking battery out for 6hours then reinstall and hard rest.
this works on mine. bob

i want make software to my i mate jasjam

The Dell Axim X30 be soft reset by pressing the "Reset" button (from the stylus tip) on the rear of the unit, below the battery.


If the Dell logo in blue background lights up and then goes off again, its probably the brightness setting of your unit. Once the device has started up, just press and hold the jog wheel (the volume wheel above the headphone jack on the left side of the PDA) and press the UP directional key in the front bottom of the PDA. Every press of the up key should brighten up the screen a bit.

If the above solution does not work, you probably might need to hard reset your device.
WARNING: A "hard" reset wipes the RAM and returns the Pocket PC to its factory defaults. You might (mostly) lose all your data if you perform a hard reset. Do not hard-reset your device without having a backup of your data.


The procedures for hard resetting your ppc is given in a very detailed steps in the following page:

http://www.pocketpccentral.net/help/dellx3reset.htm

This is usually called the "Blue Screen of Death" and the system tries to dump memory

See if you can Read any of the text which may detail the error

Try starting it in safe mode by tapping F8 every few seconds during startup

If it starts post back and i'll tell you how to use system restore

If it still fails then call in an Engineer

Same problem. Soft and hard reset can't even stard any advice screen. When the problem started, it was frozen at the dell round simbol, that i just could turn it off by removing battery. Now, its even worse, the screen is off, even after pressing the two and tree buttons at the same time, it doesn't hard reset. What else should i do?

With much regret I did a hard reset. It appeared that some how in my carrying case that hard reset got started and I could not get it out of the lock up with out taking it clear through. I hadn't backed up for a couple of month but didn't loose much data. Thanks for the follow up.

probrably your touch screen component got broken when you drop it thats why it no longer functions....