Question about Onkyo SKS-HT510 System

1 Answer

Everytime I go to turn on my onkyo it clicks twice and turns off and I see a blinking standbye light, it was playing fine then it started to smell like it was overheating

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

1.Disconnect ***ALL*** your speakers
2.Turn on unit again
3.If the unit still goes in to standby - you've damaged the amp section
4.Amp section repair is for qualified techs only
5.Take unit to repair shop for *AN ESTIMATE*

Posted on Jul 16, 2009

  • John Roeper Jul 16, 2009

    1.Disconnect ***ALL*** your speakers

    2.Turn on unit again

    3.If the unit still goes in to standby - you've damaged the amp section

    4.Amp section repair is for qualified techs only

    5.Take unit to repair shop for *AN ESTIMATE*

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I dont know if my amp is blown or not


Usually you will smell something weird if your amp is fried and it would make a pop noise.

But all amps are different. I say its time to be shopping for a new amp

Apr 27, 2010 | Volfenhag ZX-7190 Car Audio Amplifier

2 Answers

Stays in standbye and will only flash green (power on) twice before staying in standbye


The 6 inverter transformers on the bottom of the picture is the problem and what need to be tested.
Unplug the 6 wires that goes to the LCD screen. Use a multimeter to test for resistance from each output plug on the board. The one without the resistance is the bad one.
If this doesn't locate the bad one this way, Each plug should give out DC voltage if working properly. Test each plug for voltage.
The TV will automatically turn off in a couple of seconds like before. You'll have to keep pushing the power button to test each output plug for voltage.

Soon as you find the bad Inverter Transformer, just solder in a new one and the TV should work fine after that.
The part # for the Inverter Transformer is LTZ2PC0MS008.
Here's two places to get them:
http://www.partstore.com/Part/Funai%20Corporation%20Inc/Funai/LTZ2PC0MS008.aspx

http://www.encompassparts.com/products/?LTZ2PC0MS008

Apr 23, 2009 | Televison & Video

1 Answer

Apex Digital 19" LCD wont turn on green light blinks


you can have a electronics repair done on this unit call 719 687 6997

Jan 14, 2009 | Apex Digital AVL2076 20 in. EDTV-Ready LCD...

3 Answers

CORRECT SETUP CODE FOR RECEIVER


Originally Posted by 3FingeredGlove viewpost.gif We can make this work. You didn't mention which setup code you're using, or explicitly say whether the OK/Select button is red or gray (the manual you're using is for gray), so these are somewhat generic instructions. Should work, though. This will provide a power toggle function to the Power key.

Use red numbers for the red OK/Select button remote, grey numbers for grey button remtoes.
Temporarily assign setup code 30842 or 0842 to AUX
1) Tap AUX
2) Press Setup until 2 blinks
3) Enter 30842 or 0842The remote should blink twice

Assign NEC1 IR protocol device 210, subdevice 108, function number 203 to Power (you don't need to understand these numbers)
1) Press Setup until 2 blinks
2) Enter 994 (2 blinks)
3) Tap Setup
4) Enter 00051
5) Tap Power (not All On)
The remote should blink twice

Assign setup code 30135 or 0135 to AUX (this is NEC1, 210.109)
1) Tap AUX
2) Press Setup until 2 blinks
3) Enter 30135 or 0135
The remote should blink twice

Nov 15, 2007 | Onkyo HT-SR800 System

2 Answers

Will not turn on


could be the power supply or the logic board

Sep 04, 2006 | SVA-USA HD4208TIII-VR 42 in. Plasma...

Not finding what you are looking for?
Onkyo SKS-HT510 System Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5126 Answers

The Knight
The Knight

Level 3 Expert

74211 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...