Question about Televison & Video

1 Answer

[2] 811 dishnet receiver

HAVE THESE TWO RECEIVERS 1 DOWNSTAIRS AND 1 UPSTAIRS WHEN YOU GO TO CHANGE CHANNELS ,IT CHANGES BOTH SETS. I TOOK ANTENNA OFF 1 SET ,BUT DOES;T WORK ON THAT SET WITHOUT ANTENNA HOW CAN I STOP IT FROM WORKING BOTH SETS AT THE SAME TIME THANK YOU D.S.

Posted by on

  • decker Nov 18, 2007

    i hope you can help

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 50 Answers

You need to program one remote with a different code, power off or unplug one of the receivers. Go to the other receiver and hit the system info button at the receiver. Now read the remote code at the bottom of screen would be a number between 1 to 15. Program the remote for a different code than what it shows. Push and hold down the sat button on the remote and leave go light will blink, enter code say 14 and the pound key. You will see the light blink 3 times on the remote. Now that code is entered in the remote now with that system info screen up on the tv watch at bottom where code is and hit the record key on remote and you will see it change to 14. All done . now just plug back in your other receiver.

Posted on Nov 20, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We just dvrs hooked up a few weeks ago.when I am recording somthing down and my daughter goes upstairs to watch her tv and tries to change her channel to watch somthing a message comes up on the tv that...


Hi, poog_23350, I caught your post! How a Duo DVR receiver works is that the TV you have it set to record on will not allow you to change the channel while the recording is in progress. The other TV, that isn't recording anything, can be used freely to flip through channels.

In this case, it's TV2, the one upstairs in your daughter's room, that's currently set to record on while the downstairs TV is free to use. This can be adjusted by pulling up the Main Menu with the Menu button on the remote, selecting option 8, then option 5, and changing the TV1/TV2 setting there on the Record Plus screen.

If you'd like a receiver capable of allowing channel changing while recording a program, our VIP 612 receiver is a Solo receiver that acts like a Duo. What this means is that it has one TV output and two tuners. Along with being able to change channels while a recording is in progress with this type of receiver, you can also record two programs on two different channels simultaneously.

Hope that helps!

Aug 29, 2011 | DISH Network DVR-625 DTV Receiver /...

1 Answer

How can I move a receiver to another room that has . For example, downstairs i have my two receivers with 1 DVR that controls 2 TVs the one downstairsTV#1, and 1 upstairs TV#2. The other dish, controls TV...


Hey there! Becki Barned from Dish Network customer service here!!! If you want to do this! You would need a tech to come out and install the DVRs in the new rooms. If you try to move the reveivers, you will only get an Acquiring Satellite Signal message. If this has not been resolved, you can find us on Twitter, or blog back!

Nov 28, 2010 | DISH Network 311 2-Room System DTV...

1 Answer

Nikkai 2727 Video sender will not send signals from my sky+ box. The scart lead is plugged into the Video out, but even when i plug it into the TV out it still doesnt work. I know the Transmitter and...


check that you have the sender plugged into the sky box and the receiver into the required tv and not the other way round. The wrong way round still allows the controller to change channels but you will see nothing also ensure that both sender and reciever are on same channel 1 to 4

Jan 24, 2010 | Panasonic Televison & Video

1 Answer

Hi, I have a digital tv plugged into an extension cable in an upstairs (Toshiba) bedroom; it works perfectly - receiving all channels. I have a digital tv downstairs (Samsung) where it seems the wall...


Hi Fiona
Somewhere along the line from the aerial there must be a signal splitter that feeds the upstair and downstair terminals.
Try to find that splitter and switch the output to see if the problem goes from up to downstair.
If it does switch then you know the problem is with the splitter block, and if it stays the same then the problem is with the cable and/or the connectors that run downstairs.
Also the reason you get a pixellated(snowy) picture is because of signal loss during the length of the cable you ran downstair.
If running a cable downstair becomes the best option to fix your problem , then you could buy a cheap 10db signal booster/r.f amplifier to correct the signal loss and a cable splitter to feed both tv`s
That booster would be installed upstair in your case(near the source of the signal to be amplified).
I could send you a small diagram if need be. Hope this will help and Merry Chrismas

Dec 14, 2009 | Televison & Video

1 Answer

We have a tv upstairs and one down stairs, they


Since the antenna is on the roof the signal has further to travel to get to the downstairs antenna and as a result the signal is weaker. Install a device on the antenna line before the first TV called a signal booster. This unit plugs into the wall and gets connected to the antenna wire too. It will improve the signal for both televisions.

Aug 14, 2009 | Televison & Video

1 Answer

Playing vcr causes new digital tv to lose saved channels


Vizio representative suggested connecting antenna directly to TV and not through the VCR. In doing this, we lose the ability to record on the VCR but we record elsewhere and watch downstairs. The problem is solved on losing channels. I must add that we watch and record on a Sharp digital TV upstairs and do not lose channels. I don't know why the VCR had this effect on this Vizio TV.

Dec 01, 2008 | Vizio L37 Television

7 Answers

Problem connecting to my network


What I would do is replace the wireless router with a 4 or 5 port switch to control computers (devices) downstairs. Or, if you need wireless access, purchase only an access point to cover downstairs.

This way the wire from upstairs goes directly into the access point and you have wireless access downstairs.

And yet another way would be to purchase Airlink 101 PowerEthernet boxes ($54.99 each) and use those to connect an access point anywhere in your home that has an outlet.

d50fbc7.jpg

Nov 19, 2008 | Linksys Wireless-G WUSB54G 802.11g/b

1 Answer

Sky upstairs


Yes on the back of the box there is a RF2 output...

run a coaxil aerial cable from there to your required TV, you then need to tune the 2nd tv to the sky box.

You can also buy a 'Magic Eye' and a 'extra remote' this will allow you to change channels from the second destination with only 1 digi box.

Down point is that you have to watch the same channel on both tv's.

a second card and box and a dual LNB will allow you to watch seperate channels.

Jul 20, 2008 | Televison & Video

1 Answer

Digital television signals


What type of digital tv signal? Satellite or OTA (Local Digital Antenna Channels)?

What type of equipment is the split signal going to? Straight to the tv's or some sort of Satellite or HDTV Tuner box?

Dec 19, 2007 | Motorola HDT101 DTV Receiver

1 Answer

Dishnet 811 unpluged during downloadfrom satellite


yeah that is a software download, if it does not progress it may have an issue, those receivers are being discontinued, call dishnetwork and they will provide you with a replacement leased receiver and a new dish install to receive all current hd programming

Sep 04, 2007 | DISH Network 811 HD DTV Receiver

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75289 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Cindy Wells

Level 3 Expert

5380 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...