Question about Honda Pressure Washer PSI 3000

Open Question

Mixer witch way does a conrod fit in an honda g100 engine, it s not a car it s a cement mixer

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 20 Answers

SOURCE: Honda g100 stationary engine starts and runs well

Not getting enough gas.. check gas filter.. Rust/Water

Posted on Jul 07, 2009

  • 608 Answers

SOURCE: what kind of oil do

Hi, sae 10w-30 mineral oil. Hope this helps, regards Phil.

Posted on Jul 24, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Drive belt for kinzo electric cement mixer

Driver belt for kino electric cement mixer

May 13, 2015 | Masonry Tools

1 Answer

I need wiring layout for husky cement mixer?

Cement mixers aren't motorcycles. You could try asking Husquvarna for a diagram, they will definitely have one. It can't be that complicated thiough. They are usually diesel and so only have a very basic electrical system, Start and stop circuits and maybe a heater for the engine.

May 11, 2013 | Motorcycles

1 Answer

Why are the mixer barrells on cement trucks always turning?

The are always turning if there is wet cement inside. Because wet cement settles really quickly so if it isn't turning it will dry on the bottom of the mixer.

Jan 10, 2013 | Masonry Tools

1 Answer

What kind of oil do I use for a gx240 8.o honda motor cement mixer

Hi, sae 10w-30 mineral oil. Hope this helps, regards Phil.

Jul 23, 2011 | Honda 8 HP Engine

1 Answer

How fit a new conrod kit in to the crank shaft of a 2008 honda crf250

hi, the con rod kit is a press fit and requires the crankshaft removal, presing apart re fiting the new conrod and then it will need to be ballanced, specalist job,

Dec 16, 2010 | Honda CRF 250 R Motorcycles

2 Answers

Waker plate with honda g100 2.5hp engine leaking oil

jet wash it clean , then get an old tyre and start up the **** leave it on top of the tyre and just observe , we commonly used to find a small oil leak from the filter foam wiith folk leaving them on there side

Sep 11, 2009 | Hammering

1 Answer

Eng.t/plant 1.6 applause into g100 3cyl

It's doable. Some of G100 series (G100, G101, G102) had the fours fitted, so you should be able to do a cut and shut from a donor car.

The 1.6 HDE engine is pretty much the same physical dimensions as the 1.3 HCE and 1.5 HEE. The HDEG is the Detomaso version, which includes a different cam profile, higher compression and extractors.

Beware the infamous G100 chassis cracks around the front suspension, if you decide to raise the ponies..

Dec 18, 2008 | 1988 Daihatsu Charade

Not finding what you are looking for?
Honda Pressure Washer PSI 3000 Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Garden Experts

John Trevino

Level 3 Expert

1388 Answers


Level 3 Expert

2527 Answers


Level 3 Expert

78289 Answers

Are you a Honda Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides