Question about Vizio L32 32 in. LCD HDTV

Open Question

I HAVE REPLACED THE FOLLOWING; INVERTER BOARD, MAIN PANEL BOARD, AND T-CON BOARD, STILL NO PICTURE..

.I HAVE NOT SWAP THE POWER BOARD...I DID NOTICE A BLACK SUBSTANCE BENEATH THE POWER BOARD...ASSUME IT WAS DUST

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2337 Answers

SOURCE: Vizio L32 hdtv10a..

Symptoms of a Defective or dying Power supplies on LCD TVs.
1. Light(s) on the front panel are behaving not normal example, blinking, amber color or
not steady, fainting, etc.
2. TV not turning ON properly.
3. TV turns OFF by itself.
4. Needs to be unplug to many times to make it work.
5. Humming or high pitch noise heard through speakers or at the back of the TV.

Posted on Dec 15, 2008

Ad
  • 718 Answers

SOURCE: Vizio L37hdtv10a fails to fully turn on

You will have to isolate the main board and Inverters.
Unplug the inverters and turn on the set.
If it "turns on" then try re-connecting each inverter seperately to see if only one is causing the problem.

Posted on Mar 07, 2009

alpug
  • 1961 Answers

SOURCE: my vizio gv42l fhdtv 10a picture flickers like a

you need to check first the power supply board whether the output supply 12-24vdc for the inverter board is stable and not flactuating..you can measure the output voltage with a multitester..you get a voltage output of 12-24 with the inverter board is connected or loaded to the system.be carefull of the high voltage at the inverter board..once the output is stable replace the inverter board or you can measure the output of the inverter be very carefull..the output range upto 500vac.be carefull..if the high voltage is stable replace the lamps...tnx and good luck..

Posted on Jun 03, 2010

Testimonial: "Thanks again. :)"

budmrtn
  • 11361 Answers

SOURCE: Vizio SV470XVT1A has no backlight

The 24vdc is turn on by the signal from the main logic board, it is not always on, the standby 5vdc is always on. So yes it can be the power supply board is bad, but just to besure we need to find out if it is getting the turn on signal from the main board first.
You can have 24vdc at the inverter board and it will not light up the CCFL until it gets the signal from the main logic board to turn the lamps on (this is the STANDBY condition, the TV is on but the screen in not lit up util it see the video signal).
Send me good clean and clear pictures of the power supply board, budmrtn@aol.com, connectors of the Power supply, bottom side of the board, then I may be able to tell you which pin is a control input pin. Most people will just throwing parts in and hope that they one of the parts will fix the problem. Used Power supply module for this TV is over $100. http://www.google.com/products?rlz=1T4GGIH_enUS282US283&q=delta+DPS-379AP&um=1&ie=UTF-8&ei=USsxTKn3J6TonQfFlJGEBA&sa=X&oi=product_result_group&ct=title&resnum=4&ved=0CCsQrQQwAw

http://www.shopjimmy.com/catalogsearch/result/?q=Vizio+SV470XVT+

Posted on Jul 05, 2010

Testimonial: "Bud helped me fix my TV! It was only 1 1/2 years old. I was looking at a repair bill close to $300 - $500 and I fixed it with a $60 board! Thanks!!!"

  • 12 Answers

SOURCE: I have a vizio vz37l tv. When i turn it on the

its the main board...

Posted on Mar 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Samsung TV - No picture but sound


Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Sep 11, 2016 | Samsung Televison & Video

1 Answer

Which part causes backlight flickering / dimming?


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

May 02, 2016 | Samsung UN46FH6030 46" Class 1080p LED...

1 Answer

Vizio 55 inch led sound but no picture


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis....
http://electro-medical.blogspot.com/

To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Apr 12, 2016 | Vizio Televison & Video

1 Answer

LG LCD Tv - No picture but have audio and new t-con board. What board to replace next?


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Apr 07, 2016 | LG Televison & Video

1 Answer

My Phillips 47 LCD TV is loosing picture but is keeping sound.


Main board feeds the t con board. However try the flash light test on set because it might just be the inverter board that powers the backlighting.

Mar 17, 2016 | Televison & Video

2 Answers

Philips 40pfl3705d/f7. Why is there no picture?


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced.

Feb 05, 2016 | Televison & Video

2 Answers

I have a 50" element tv. Model # ELEFT502 The picture went black but sound still works. when u take a flashlight to it u can still see the picture. Easy fix??? Also where/how much would the part be?!


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced.

Jan 11, 2016 | Element Televison & Video

2 Answers

VIZIO E472VLE Will not power on.... I have changed the power board and the main board but it will not power on. Does anyone have a schematic for this TV?


First check the inverter boards,if inverter boards is defective,you also could not turn on your tv.
if not you need check main boards,
From Wisiny.com can find those parts,power supply,inverter boards and t-con

Sep 26, 2013 | Vizio 47 E472VL 1080p 120Hz Widescreen LCD...

1 Answer

I type slow, I have a Vizio M261VP LCD TV, I purchased it not working. I purchased a new power supply. A light comes on and flashes in lower right hand corner. I t does not flash on and off it flashes...


Good day sir chris!!!!

Welcome in fixya and I'm happy to work with you...

OK lets proceed to your TV problem..

The possible problem is not the power supply...There some shorted parts on inverter board,T-con board or main board so that the power will not initialize due to that shorted problem..

I teach you how to find which board is shorted or cause of that fault..

Just follow this procedure below.
  1. Open the back cover
  2. Look at the inverter board..it is slim board that have small transformer on it.
  3. unplug the inverter board first.Then try to power it on...
  4. If the LED on front of TV will not flashes from bright to dim it means you have shorted inverter board try to replace it..
  5. If the flashes remain..go to next step..Power off tv then reconnect inverter board,after that unplug T-con board..Then power on.
  6. If the LED on front of TV will not flashes from bright to dim it means you have shorted T-con board try to replace it..
  7. If all those procedure done but still problem persisted the only problem is main board..Replacing main board will fix the problem..
NOTE: When unplugging and replacing of all board make it sure to memorize all connection or its better if you take a picture on it for future reference..

Hope this solution will be helpful..Any rate will much appreciated..

Thanks for using fixya..have a nice day!!

Mar 04, 2012 | Vizio M261VP 26" LCD TV

1 Answer

81@hI have a LA32B550KIF LCD TV by Samsung. Just recently the picture has gone but we still have sound. Is there a step by step manual that I can follow online to reset the settings? I have currently...


Hello destinee81, let me help you.
I often see things like that, mostly occurs because the problem panel.
To ensure it, first turn tv on than wait a minute until you hear a sound from a channel tv.
After you hear a sound and still no pict, knock gently the panel with your hand ( not too hard but not too soft). If you see a flashing light (on area you knocked) , that mean back light panel is OK. Open rear cover , there are 2 boards (Power board and Main board) and 2 board attached on panel (inverter and T-con) , "beware with high voltage on power an inverter board". Check connection on t-con and main board, clean it with brush to remove dusts on it. if still make no changes , replace the t-con board.

mas_baz_19.jpg

Second, repeat first step above. If there are no flashing light on knocking area,. that problem from inverter board. Replace it. If any problem and questions, please let me know.
I hope that will help you. Thanks.


Mar 23, 2011 | Televison & Video

Not finding what you are looking for?
Vizio L32 32 in. LCD HDTV Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vizio Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76046 Answers

Tony Nguyen
Tony Nguyen

Level 2 Expert

96 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Vizio Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...