Question about Teac Audio Players & Recorders

1 Answer

My TEAC AG-7D turns on for about a second but then turns off

My TEAC AG-7D turns on for about a second but then turns itself off. Wont stay on for more than a second.

It happens when the speakers are fully disconnected too.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,234 Answers

There is a problem in the final stages of the amplifier section that the protection circuits are detecting. They then shutdown the unit to prevent further damage. The most likely candidates are the output transistors. This is a relatively simple repair for an audio shop. Expect a parts cost between $20-$45.

Dan

Posted on Jul 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have this issue, my teac ag d7900 which itself off to standby and when I switch it "on" again, it says protect and shut itself down again


Right. This means that either you have a short in your speaker cable somewhere or the short-detector circuitry inside has problems. Disconnect all speaker cables and turn the receiver on. If the symptom goes away, turn the receiver off again and connect one of the speaker wires. Repeat until it starts to go into protect again. When it does, the last speaker you hooked up has a short somewhere in the wire.
If protect always comes on, you'll need to get the unit serviced.

Jun 28, 2015 | Teac Audio Players & Recorders

2 Answers

Teac ag-d9100 center and surround speakers are not working , very very low volume.. the others all work fine. Anybody know where to start troubleshooting. Its not a fuse that I can see , at least that i...


You have to enable them and turn the volume on them up separately with the speaker config, level trim, and up/down select buttons on the remote. You can also adjust the rear speaker delay time or just hit the test tone button and adjust the volume on each speaker separately as it goes through them one at a time...

Jun 01, 2010 | Teac AG-D9100 Receiver

1 Answer

Teac AG v6200 wont stay on


Check your speaker wires, if they are crossed somewhere then the system protects it's self.

Jun 22, 2009 | Teac Audio Players & Recorders

1 Answer

Teac AG-V8520


same problem exactly

Oct 13, 2008 | Teac AG-V8060 Receiver

1 Answer

Teac AG V7700 Receiver problem powering up


I have a Teac ag-7700 and when I would try to power it on it would shut off. I did get it to turn on for about 10 minutes and then it shut off. Now when I try to power it on the light on volume dial stays lit but the LED does not light up and no sound through speakers.

Jul 30, 2008 | Teac AG-D8900 Receiver

2 Answers

Lost manuel for teac ag d9100 reciever


you can download a manual for $9.99 from User-Manuals.com....I did this today and the manual is identical to the original it seems

Jul 11, 2008 | Teac AG-D9100 Receiver

1 Answer

Teac AG-L800 'Protect' Error


Since the problem appeared to correct itself on occassion, I would first look for poor solder connections either at the output transistors or at the voltage regulators. Let me know if you need more detail.
Dan

Mar 18, 2008 | Audio Players & Recorders

3 Answers

Teac AG V8050


try using an antenna.

Dec 09, 2007 | Teac AG-V8600

1 Answer

TEAC Amp


The amp is going into "protect mode". This means there is a bad part or parts being detected. Professional service will be needed.

Sep 13, 2007 | Teac A-1D 2-Channel Amplifier

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Teac Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5011 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

The Knight
The Knight

Level 3 Expert

73619 Answers

Are you a Teac Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...