Question about Polaroid TTM-2401 TV

1 Answer

Chuy i have a problem with this tv when i turn it on the tv seems turn it on but in 3 seconds seems turn it off and a relay sound is present and this happen about 3 or 4 times and then the sound of the relay turn it off and the tv stay in stand by and when i try turn it on again it don´t respond. the voltage in horizontal transistor is 136 volts in the momen that the tv turn on and then go to 88 volts when turn it off. please help me with this problem. thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Polaroid Master
  • 1,689 Answers

The power supply is going in to protection. There is a short somewhere.

Since you sound like you are able to service the set, remove the CRT socket and see if the set starts up and has high voltage. If so, the CRT may have a short in the electron-gun, or it is being over-biased from the CRT board.

I don't know the particular model design of your set. In the models that I do know, I have had components on the CRT board go defective and cause over-biasing of the CRT and cause a shutdown on startup.

Sometimes the components on the CRT board fail because the CRT is at fault, and it is arching some very high voltage back out to the devices on the CRT board. In this case, they will soon fail again.

If the above does not work, then it is possible that the flyback transformer has some shorted turns, or there is a failure in the HV multiplier.

Other things that can cause a shut down is if there is any components in any of the areas of the set that are causing too much current pull from the supply.

These sets can become very involved and a challange for the most experienced of techs to service.


Jerry G.

Posted on Apr 12, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Samsung LN-S4051D slow to turn on.


You are likely to have a module bad....part number BN94-00864A and if you take it out (unpluggs) you should inspect it for capacitors that may be domed or pooched up at the top. If so they should be replaced first before getting the module as the capacitors are about $1.00 each. Do a search for Samsung parts online if you need the module and call them toll free

Mar 16, 2008 | Samsung LN-S4051D 40 in. LCD Television

1 Answer

Kenmore 665.6061200 over range microwave. Problem started a few days ago with a clicking sound from the RH side of the unit (seemingly behind the control panel), about 3 clicks per second for about 3-4...


The most likely cause of the clicking sound is the power relay that is connected to the microwaves PCB (circuit board) that turns the magnetron on and off. If starting to fail it may result in multiple clicks, then once fully failed, your microwave would simply not heat anything (as the high voltage components would not be getting power).
Unless you have a strength in electronics and repair, and understand the lethal dangers involved in working on a microwave, even one that is unplugged, this problem will likely need to be repaired by a qualified service centre.
Depending on the microwave design and the technician the whole relay circuit board may need to be replaced making this repair vary from relatively inexpensive to more expensive.

Oct 21, 2010 | Microwave Ovens

1 Answer

No picture on my philips 42PF7321D/37


Bad caps in the power supply must be replaced .

Jul 21, 2009 | Philips 42PF7320A 42 in. Plasma HDTV

1 Answer

Startup Problem with my 42pf7321d/37 Phillips plasma TV


I need to know how long do you have the tv?In the other word,approx. how many hours you have put into it?
Secondly,did you wall mounted the tv or setting it close the the area which there is not much room for the back of your tv to breath?
solutiondoct

Nov 06, 2008 | Televison & Video

1 Answer

No picture yes sound


I was told that this problem could be the power board.

Jun 17, 2008 | Televison & Video

1 Answer

My TV cannot turn ON


1 check for short on HOT (horizonal output transistor) or bad flyback transformer. 2 check the AC voltage on the relay switching side. if AC voltage is not present on both pins and the relay is engaged replace the relay.3 check for shorts on voltage regulators you will need a schematic for this.

Jan 21, 2008 | Hitachi 27CX7B 27" TV

1 Answer

TV turns itself off after a few seconds, no picture at all


Sounds like the typical Flyback and shorted horizontal output transistor. Problem is the transformer is NO Longer Available

Sep 13, 2006 | GE 32GT740 32" TV

Not finding what you are looking for?
Polaroid TTM-2401 TV Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaroid Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75169 Answers

matt martin
matt martin

Level 3 Expert

1213 Answers

Jaime Hernandez

Level 3 Expert

2335 Answers

Are you a Polaroid Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...