Question about Furuno NavNet vx2 1920C GPS Receiver

1 Answer

My furuno navnet vx2 periodically freezes during operation and must be restarted. Any suggestions?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 132 Answers

Reinstall the operating software. The unit should probably go to Furuno.
Try operating it with only a GPS connected (no radar, no network). If this resolves it, it is almost certainly software. It could be low voltage or failing mother board.

Posted on Jan 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the "toolbar" from the top of the screen on my furuno NavNet Vx2?


go to toolbar with controller, and push clear key. just it.. but when you restart your system, it appears again. if you wanna lose it anytime, you must do it inside the General Setup.

thanks..

Dec 21, 2012 | Furuno NavNet vx2 1920C GPS Receiver

3 Answers

Ais and 1920c Furuno chart plotter


n the system setup, under “UNITS” I set BEARING to “MAG” (magnetic). This will cause the unit to display course / bearing information in relation to the Magnetic North and match magnetic compass readings. It is not the same as True North! One has to be careful with this setting. There are a number of areas where the earth's magnetic field is locally disturbed, sometimes very significantly. Your GPS may not account for it. - again, under “UNITS” I set “METRIC”.

Sep 02, 2008 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

I have a Furuno Radome RSB0094-075 with a Navnet RDP 139 10.4" What I dont have is the antenna cable to connect the two units. What cable should i be ordering for this?? Thanks, Mike


That is a Furuno 1823C Radar -000-138-972 (10 meter Radar cable) $150.00 msrp from Furuno. Give their Camas Office a call or your nearest dealership. The Furuno number in Camas, Wa 888-834-9330

Nov 06, 2010 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

How do i connect my furuno navnet vx2 to my vhf radio. i have a 6 pin nmea cable for the vx2. but i do not unerstand which wire to use.


the output is on the black (blue) and white wires. in system setup, portsetup, you can select which sentences it sends out. 847-746-0100

Jun 17, 2010 | Furuno NavNet vx2 GP1720C GPS Receiver

1 Answer

How do i reboot my furuno navnet......recently installed radar and system not recognising teh radar installatio. no count doen on radar page greyed out overlay icons on the screen


Press and hold the "MENU" button during power on. Release "MENU" after boat appears.
Go through the installation wizard. You must select the radar type, "B" is 1834.

May 21, 2010 | Furuno Navnet 1834C/NT vx2 Radar C Map Nt

1 Answer

My 1734c will not boot past the black disclaimer


This is a bit of bummer. Usually (and I hope in your case too) it is just a software problem. As a navnet is basically a computer this can happen. First I suggest you unplug everything except power and start it up, just to see if something on the network port isn't messing it around. If it still gets stuck take it to your local Radio Holland office or another furuno certified service outlet to reload the software.

Mar 27, 2010 | Furuno Navnet 1834C/NT vx2 Radar C Map Nt

1 Answer

Need owners manual for furuno navnet vx2 1834c


easy one, download here
http://www.furunousa.com/Products/ManualList.aspx?category=Products+%3a+NavNet+vx2+%3a+Radar+%2f+Chart+Plotters

Feb 22, 2009 | Furuno Navnet 1834C/NT vx2 Radar C Map Nt

1 Answer

I can not seem to get a simrad ap 20 to recognize the nmea connection from the navnet vx2


you will have to designate which sentences to send to the AP20 from the navnet under port options. also make sure the AP20 is set to read the correct port to accept the information such as gps1 or 2 or nav1 or nav2

Jun 29, 2008 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

Software


Buy it from a Furuno dealer like me The product is MaxSea NavNet version John Barry 847-746-0100

Feb 07, 2008 | Furuno NavNet vx2 1920C GPS Receiver

Not finding what you are looking for?
Furuno NavNet  vx2 1920C GPS Receiver Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Furuno GPS Experts

Cindy Wells

Level 3 Expert

5186 Answers

Steve
Steve

Level 3 Expert

694 Answers

The Knight
The Knight

Level 3 Expert

74459 Answers

Are you a Furuno GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...