Question about Maytag 24 in. MDB3700 Built-in Dishwasher

1 Answer



Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 20 times.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 18 Answers

I suggest calling Maytag and have a tech come out to look at it. Appliances come with a one year parts and labor warranty.Use it before your one year is up.

Posted on Nov 18, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Water not draining

Hello Jerry;

My name is Peter. I am a retired field service appliance technician.

You did not provide a model number so I can only advise in general terms.

If your hose has blown, then your pump is working. I suspect your drain hose is plugged up with soap film, broken glass .....

Clean your drain. Use gloves. You may have broken glass in the drain. If you have a filter clean that. Remove your drain hose and flush it.

If you have a dish washer that requires a special detergent, and you are using a less expensive brand, you are looking for trouble.

After you have completed the above, purchase a dishwasher cleaner and run that.

Dec 22, 2014 | Miele Dishwashers

1 Answer

Dish washer will not turn on or start! It is plugged in and connected to water


First make sure that nothing is blocking the drain pump assembly located inside the lower front panel of the dishwasher. If the issue returns after its cleaned then it means that the control board has gone bad and should be replaced. Hope this helps...please post back for further assistance.


Jun 28, 2011 | Maytag Dishwasher

1 Answer

The Dish Washer is Not Hot enough

If an adjustable thermostat is provided adjust the dial. If it is an electronic type, check the sensor with a correct part no.

Refer user guide also for the adjustments.

May 27, 2010 | Jet Tech Systems 24 in. F18DP...

1 Answer

Dish washer 3 1/2 yrs old making a growling/vibrating sound.

The problem is hard water. There is a new product out called the dishwasher filtration system. It filters the water before it enters your dishwasher. It works amazing and has a money back guarantee. You will love the way your dishes look after the first load. It is also very affordable (like 70 bucks). Go to to find out more info.

Jan 28, 2010 | GE 24 in. Profile PDW9880JSS Built-in...

1 Answer

My dishe washer wont turn on

Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced

Now, if you have confirmed that the unit is receiving power from the outlet, and the unit is still not responding, this will lead to a failed control board, or timer module. replace either the timer, or control board, in this case.

Nov 05, 2009 | Dishwashers

1 Answer

Blew a circit breaker this morning dishwasher wont start all power in kitchen is working this is a 1 1/2 year old dish washer

I am sure that you know that the dishwasher is on its own circuit... and that, in an older home that has been upgraded, the dishwasher may be on a GFI circuit.... If I am correct, you have an open GFI circuit somewhere in the kitchen or in a first floor bathroom.... that is feeding the dishwasher...

If all breakers are 'on" and no failed GFI is found, the the bad news is that the program chip in the dishwasher has been fried...
If that is the case, you may be better off replacing the dishwasher than in replacing the chip in the old one.

Oct 17, 2009 | Dishwashers

1 Answer

Maytag legacy series 3 yr's old

I had a similar problem where slowly specific buttons stop working. Moisture was getting into the control board and slowly killing buttons. I replaced the control board and that worked for another year, until the buttons began dying again.

For now, there are other ways to start the machine, but you just have to let time expire to stop it. It is probably a control board issue.

Dec 12, 2007 | Maytag MDB7100AWB Dishwasher

2 Answers

Dishwasher Heating element not working

rclay How old is your dish washer? It has up to five years limited (parts only) warranty on the electronic control. If it is within this period of time, then you can call Maytag and they will send you a new part. If you are not sure how old is it, you can find it with Maytag by the model and the serial numbers (on the door frame). The warranty for your dish washer you can get here: back

Jan 31, 2007 | Maytag MDB9100A Dishwasher

Not finding what you are looking for?
Maytag 24 in. MDB3700 Built-in Dishwasher Logo

Related Topics:

546 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides