Question about Kodak EASYSHARE 5100 All-In-One Printer

3 Answers

I have a kodak aio esp07 printer. I'm getting a 3802 error - what is this?

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 154 Answers

This is a Printhead Error and cant be resolve, call kodak and they will gonna replaced your Printhead.
Kodak Tech Support 1800 421 6699
Thanks

Posted on Aug 14, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The solution from the support line provides no result! I too have had this error on my ESP7 printer and when I removed the print head found ink on the bottom side. After cleaning this off of the print head I returned it to the printer and ran the calibration which prompts you automatincally, and the problem goes away. I print a fairly large volume as I use this printer daily so this fix lasts for about 2-3 months for me and I have performed this 3 times to date with positive results each time.
I have contacted Kodak support and shared this with them and they wanted to send a replacement print head at my cost... I don't think so... and the repeated cleaning they ask you to perform simply will use up more ink again at your cost... As a point of reference I have 30 years in the computer systems area with some printer knowledge from bench level repair at a Mfg some years back as well as some design experience so have suggested Kodak provide a fix to keep the print head from getting contaminated from this ink, no response yet from them...
Rick

Posted on Aug 08, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 119 Answers

To resolve the error condition:

  1. Open the Printer Access Door.
  2. Remove and install the Printhead two times before closing the Printer Access Door.
  3. Wait until the printer is ready to use.
  4. Close the Printer Access Door.

If the error condition continues, contact Kodak.

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why will my printer not print. shows error 3802. just prints blank page. do have ink.


Error: "Printhead Failure" (105-3802) - Kodak

support.en.kodak.com/.../error%3A-printhead-failure-(105-3802)

KodakAug 25, 2010 - How do I resolve the error message "Printhead Failure" (error code ...If you are not prompted to calibrate the printhead, turn off the printer, wait ...

Error: "Printhead is missing, not installed correctly, or has ...

support.en.kodak.com/.../error%3A-printhead-is-missing,-not-inst...

KodakAug 25, 2010 - How do I resolve the error message "Printhead is missing, not installed correctly, or has come loose" (error code 105-3513) on my ESP or HERO All-in-OnePrinter? ... If the printhead and ink cartridges are not installed in the printer, install them: ... If the error continues, restart the printer and try to print.

Jan 18, 2016 | Kodak ESP5 AllInOne InkJet Printer

1 Answer

Error code 3802


  1. Upgrade your printer firmware to the latest version
  2. If your printer firmware is already up-to-date:
  3. If the error continues:
  4. If the error continues,
for more help visit https://cbrtechsolutions.net or
CBR Tech Solutions

Jan 19, 2014 | Kodak Office Equipment & Supplies

1 Answer

Printer will not clear the Error 3802 , what do I do?


Hello and Welcome to FixYa!
Error 3802 generally occurs in the Kodak Inkjet Printers.
To solve this error Turn the printer off and then turn on, this problem is solved by doing this mostly.If the problem still there then remove the ink cartridges and the print head and after few minutes put it back in the printer .If you are still facing this then do it again almost five times & if still your problem is not solved and you still get error code 3802 then probably your KODAK EASY SHARE 5500 All-In-One Ink Jet Printer is in need of servicing by a service professional.
I hope this solution helps you
Don't hesitate to let me know if you want any further assistance.
Thank you and Keep using FixYa!

Aug 17, 2011 | Kodak EASYSHARE 5500 All-In-One InkJet...

2 Answers

Getting problem code 3802


Hello thanks for using Fixya
Error 3802 Mean Print head Failure

Turn the printer Off and On, This problem is solved by this mostly.If the problem still there then remove the ink cartridges and the print head and after few minutes put it back in the printer .If the problem still there then do it again almost five times & if still problem not solver and you get error code 3802
then it is probably that your KODAK Esp 3250 Allinone Multifunction Printer is in need of servicing by a service professional.
So go to the KODAK Service Center


Your problem will be solved.

I hope this solution will helpful 4 u
Please don't forget to click on Four thumbs which are given below & then write testimonial in your words for appreciation "if it is helpful"
THANKS
Keep Using Fixya

Feb 28, 2011 | Kodak Esp 3250 Allinone Multifunction ( ...

1 Answer

What is error code 3802 on an ESP 5 kodak printer?


Hello thanks for using Fixya
Error 3802 Mean Print head Failure
Turn the printer Off and On, This problem is solved by this mostly.If the problem still there then remove the ink cartridges and the printhead .If the problem still there then do it again almost five times & if the problem still there then final option contact to kodak support

Your problem will be solved.
I hope this solution will helpful 4 u
Please don't forget to click on Four thumbs which are given below & then write testimonial in your words for appreciation if it is helpful
THANKS & Keep Using fixya

Jan 26, 2011 | Kodak ESP 5 Printer

3 Answers

Printer wont copy error code 3802


Hi,error 3802 Means Printhead Failure

All You need to do is turn the printer Off and On

And if the problem still there

Remove the ink cartridges and the printhead

And if the problem still there
Do it again for (5x)

And if the problem still there,
i will suggest you contact their customer care for further assistance.

Apr 16, 2010 | Office Equipment & Supplies

1 Answer

What is error code 3802?


"Printhead failure" - #3802 Solution (from Kodak website):
  1. Open the printer access door.
  2. Disconnect the power adapter from the printer.
  3. Wait 30 seconds to allow the printer to reset.
  4. Connect the power adapter to the printer. Turn the printer on if necessary.
    • After the printer completes powering up, the message "Printer access door open" will appear.
  5. Close the printer access door.

Feb 16, 2010 | Kodak ESP 5 Printer

1 Answer

What is error code 3802


"Printhead Failure" (error code 3802)
To resolve this error:
  1. Open the printer access door.
  2. Disconnect the power adapter from the printer.
  3. Remove and install the printhead two times.
  4. Wait 30 seconds to allow the printer to reset.
  5. Connect the power adapter to the printer. Turn the printer on if necessary.
    • After the printer completes powering up, the message "Printer access door open" will appear.
  6. Close the printer access door.
If error condition continues, contact Kodak for printhead replacement.

Best of Luck

Nov 17, 2009 | Kodak EASYSHARE 5500 All-In-One InkJet...

1 Answer

Printhead failure error code 3802


You need to contact kodak and ask for a replacement print head, explain the code and whats been happening.

www.kodak.co.uk

They will probably tell you to download new drivers and wash your printhead ect ect but nothing that helps.

I had the same problem with the same printer.

I couldn't get Kodak to send out a printhead, so after weeks of messing around, I took it back for a refund.

If you do manage to get a new printhead here are the instructions on how to remove and replace it.

http://www.kodak.com/global/plugins/acrobat/en/service/manuals/AiOPrinters/printhead/AUR1780-9_UE_RevC.pdf

Jan 31, 2009 | Kodak EASYSHARE 5100 All-In-One Printer

1 Answer

Error 3802


printer can not talk to printhead... power off. wait. power on

Sep 16, 2008 | Kodak EASYSHARE 5100 All-In-One Printer

Not finding what you are looking for?
Kodak EASYSHARE 5100 All-In-One Printer Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18391 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Cindy Wells

Level 3 Expert

5099 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...