Question about Dell PowerConnect 6024 24x1000 Mbps Networking Switch

1 Answer

Remove a ACE from an ACL using CLI

Hi,
We are using Dell PowerConnect 6024.

We are trying to remove one entry from the ACL, but we only have access through CLI, we don't have a GUI. What is the proper command ?

for example, we want to remove the following line :
permit tcp host any host 1433

Would it help if, instead of removing the previous line, we would just add
permit tcp host any host any ?

We tried
no permit tcp host any host 1433
but it doesn't work...

Thank you !

Also, is there a place where we could download the GUI for Dell PowerConnect 6024 ? Thank you !

Andrei.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 126 Answers

Sure thing:

First to enable the web interface, try command:

ip http server

Also try:
ip http port 80

That will enable it on the default port

As for the ACL's I looked at the documention and I believe the syntax is to put a deny in front of the command and that will remove it.

Of course the GUI will be easier to deal with

The manual can be downloaded from:

http://support.dell.com/support/edocs/network/pc6024/en/index.htm

Posted on Jul 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DHCP Users Go Online Through the S2700, But Cannot Access the Internet. Why?


When a large number of DHCP users go online through the S2700, the S2700 generates a large number of dynamic DHCP snooping binding entries. On the S2700 V1R6C00SPC800, the software provides incorrect priority settings for DHCP snooping binding entries and IP source guard and DAI ACL rules, and the ACL rules have a higher priority than DHCP snooping binding entries. As a result, the software delivers the ACL rules but not DHCP snooping binding entries. User packets cannot be forwarded because no binding entry is available.
Solution: Install S2700SPH006, enable DHCP users to go online again, and reconfigure IP source guard and DAI on the physical interface from which DHCP users go online.
S2700 Switch Thunder link com

Nov 04, 2016 | Computers & Internet

1 Answer

What is the default ip address for powerconnect 5212


You must assign an IP address to the switch to gain management access over the network. You may also need to a establish a default gateway between the switch and management stations that exist on another network segment. You can statically configure a specific IP address or direct the switch to obtain an address from a Boot Protocol (BOOTP) or Dynamic Host Configuration Protocol (DHCP) server when it is powered on. Valid IP addresses consist of four decimal numbers, 0 to 255, separated by periods. Anything outside this format is not accepted by the CLI program. notice.gif NOTICE: By default, the IP address is assigned to VLAN 1 through DHCP. If you select the bootp or dhcp option, IP is enabled but does not function until a BOOTP or DHCP reply has been received. Requests are broadcast periodically by the switch in an effort to learn its IP address. (BOOTP and DHCP values can include the IP address, default gateway, and subnet mask).
To display assigned IP settings using the CLI:
  1. From the Privileged Exec or Normal Exec level mode, type show ip interface and press <Enter>.

The assigned IP address and subnet mask displays.

  1. From the Privileged Exec mode, type show ip redirects to display the assigned gateway IP address. Press <Enter>.

The following example displays IP settings assigned by bootp or dhcp using the CLI.

Console#show ip interface

IP address and netmask: 10.1.0.1 255.255.252.0 on VLAN 1,

and address mode: User specified.

Console# show ip redirects

ip default gateway 10.1.0.254

Console#
Before you can assign a static IP address to the switch, you must obtain the following information from your network administrator:

  • IP address for the switch

  • Default gateway for the network

  • Network mask for the network

To assign a static IP address to the switch:
  1. From the Privileged Exec level global configuration mode prompt, type interface vlan 1 to access the interface-configuration mode. Press <Enter>.

  2. Type ip address ip-address netmask, where ip-address is the switch IP address and netmask is the network mask for the network.

  3. Type exit to return to the global configuration mode prompt. Press <Enter>.

  4. To set the IP address of the default gateway for the network to which the switch belongs, type ip default-gateway gateway, where gateway is the IP address of the default gateway. Press <Enter>.

  5. To save your configuration changes, type copy running-config startup-config and then press <Enter>.

notice.gif NOTICE: Only one VLAN can be assigned an IP address. If you assign an address to any other VLAN, the new address overrides the original IP address. The following example shows how to set a static IP address using the CLI.

Console(config)# interface vlan 1

Console(config-if)# ip address 192.168.1.5 255.255.255.0

Console(config-if)# exit

Console(config)# ip default-gateway 192.168.1.254

Console(config)#
To configure the switch for DHCP or BOOTP:

  1. From the Privileged Exec level global configuration mode prompt, type interface vlan 1 to access the interface-configuration mode. Press <Enter>.

  2. At the next prompt, use one of the following commands:

    • To obtain IP settings through DHCP, type ip address dhcp

    • To obtain IP setting through BOOTP, type ip address bootp

  3. Press <Enter>.

  4. To save your configuration changes, type copy running-config startup-config, and then press <Enter>.

Nov 26, 2012 | Computers & Internet

1 Answer

How do i configure the switch to allow web access through the serial port


If you can't find the manual on the Dell web site, there is a copy at: http://www.manualowl.com/m/Dell/PowerConnect-3548/Manual/188907

Did you use the command: ip http server ? See page 501 in the manual.

I would not recommend setting up a network switch with password-free access to the internet. You should at the very least limit access to a small subset of IP addresses (e.g. your network group's machines). The best practice is to use ssh communications or https with the web browser, otherwise anyone with a well-placed sniffer can read your clear-text traffic.

Sep 19, 2012 | Dell PowerConnect 3548

1 Answer

How do I get into a terminal session on a dell power connect 2124 switch?


Hello Jlhambric.

The Dell PowerConnect 2124 is an unmanaged switch. Plug and play with no interface.

Feb 25, 2011 | Dell PowerConnect 2124 Networking Switch

1 Answer

I have just 2 computers currently connected to my Dell Power connect 2124...One is accessing the internet just fine but the other cannot acquire an ip.....I put new ends on the cable but stll no soultion


I assume you have connected your switch to any broadband router and then trying to access multiple systems at the sametime.
This is not possible if NAT (Network Address Translation) is not enabled on your broadband router.

Jan 08, 2011 | Dell PowerConnect 2124 Networking Switch

1 Answer

I can not log onto my dell powerconnect 2708. I'm connecting the dell powerconnect 2708 into a hughes net modem and routing to three different locations. I would like to monitor/contol usage...


The problem you have is unlikely to be related to your server but to the modem and any ISP restrictions placed on your service i.e. it may block remote access or any port 80 traffic not originating from within your LAN. I don’t know much about your situation but it may be worth contacting your ISP to see if the functions you require are available with your hardware and contract type. Attached is a link that may help.
http://www.dslreports.com/forum/r19028526-Networking-Port-Fowarding-using-the-HUGHES-NET-Modems

Jul 02, 2010 | Dell PowerConnect 2708 8-Port Gigabit...

1 Answer

Dell powerconnect 2016 seems to have stopped working


most likly a failed power supply on the switch
look at the front of the switch look for leds,.......
if you see nothing and the power cable is plugged into a hot outlet than
go down to your neerest comp store and buy a new one

Apr 26, 2010 | Dell PowerConnect 2016 (pct2016)...

1 Answer

How can we check whether the switch can support multicast traffic


You need to verify that this switch at least L2 switch if you want to correctly handle this kind of traffic.

Apr 21, 2010 | Dell PowerConnect 6024 24x1000 Mbps...

1 Answer

Static ip address to dell powerconnect switchport for backbone


try for 195.9.200.00 - 195.9.200.32 series hope it will works

Mar 23, 2009 | Dell PowerConnect 6024F (p624fnp)...

Not finding what you are looking for?
Dell PowerConnect 6024 24x1000 Mbps Networking Switch Logo

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...