Kitchen Aid range Breaker always tripping ERROR F5:E3

Tech sheet doesn't say much says noise interference at keypad says press cancel button and remove electronic noise interference if code returns replace key pad assembly not a common code if you chose to replace the keypad make sure it comes with instructions have changed two has to be programmed

Nov 9, 2009 ... I could thump it with my fist, not hard, just a light thump, and it would come back on ... Problem with KitchenAid KESC307 Electric Kitchen Range ... the ribbon cables and the panel can be removed to a convenient work surface. www.fixya.com/support/t3391463-kitchenaid_range_kesc307hbt8_display www.fixya.com/support/t3391463-kitchenaid_range_kesc307hbt8_display
Just checked this site and it has an answer to your problem. Very complicated, but I am sure you will be able to follow it

Hello Tgilreath,

I understand that you are having a problem with you KitchenAid range. The oven element is broken and needs replaced and you would like to know the cost of the element.

I can instruct you on how to change the element in your range. However, I do not know if it is the top of bottom element and the change procedure is the same on both of them. However, when looking up the element to tell you where you can purchase and the cost I came across many different KitchenAid models that contained the numbers you gave. There should be more letters and numbers on your tag for the model.

The following is steps are how you change out your element:

1. Disconnect the power to the unit
2. Remove the lower back cover on your range (the one that sits directly behind your oven)
3. Locate the two prongs on the bad element sticking thru the oven wall and remove the wires
4. In the oven remove the racks
5. In the oven remove the two screws holding the element in place
6. Remove the element by pulling in forward
7. Install new element in Reverse

You can locate the element on Sears Parts Direct at the following web-page, however you will need the full model number http://www.searspartsdirect.com/partsdirect/part-model/kesc307?pathTaken=modelSearch&prst=0&shdMod=kesc307 You may also reply to this thread and I will get you a part number and the exact page you need to order the part.

Thank you for choosing FixYa.com

Justin

Hi,
If your electric oven is not heating then you probably have a bad heating element in your oven. This is not that hard to fix yourself...
Check out this tip that I wrote about the Oven not heating problem..

Oven Problems Electric Oven is Heating Slowly or Poorly
http://www.fixya.com/support/r4511800-oven_problems_electric_oven_heating

heatman101

We've seen similar problems due to an intermittent failure in the control board. If you can have it removed we can likely repair it for you.

Best Regards,
Bruce
www.fixyourboard.com

This happened to me just yesterday! I had unplugged the range and moved it out of the way while I installed a microwave and this happened after I plugged it back in and moved it back I set the time into the clock but had forgotten to set the time I guess....because when I pressed clock again it stopped.

KitchenAid KESC307

The bulb inside the oven is 40 watts appliance

You did not indicate which bulb you need but you can go to
http://www.appliancepartspros.com/partsearch/model.aspx?model_id=251681

and click on the diagrams in the left-hand side to locate the bulb you need.

Did you replace burnt fuse/tripped breaker?

"cycle the circuit breakers" is to turn the switch for the stove at the electric switch box at the main feed of the house electric panel. This is equivalent to unplugging the stove and plugging it back in.

In the old days, a circuit breaker was a "fuse" in the "fuse box"...

We have called a technician, who believes it may be the switch.