Question about Boating

1 Answer

Tilt-trim not tilting down after being tilted all the way up

Tilt-trim is working going up, but not going down when tilted all the way up.

Posted by on

  • Anonymous Mar 29, 2014

    cannot get pivit pin out

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Check the solinoid you should have two,one for up and one for down,you can test by putting a screwdriver on both neg and pos contacts at same time,if thats not it check to make sure nothing came unpluged

Posted on Jul 26, 2009

  • douglas hughes Apr 08, 2014

    put 2 new ones on and no power it the plug

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When tilting the motor down it jumps and bangs until it gets to the trim pistons, what is causing this?


Power Tilt and Trim Maintenance Makes a Difference ...

yamahaoutboards.com/.../power-tilt-and-trim-maintenance-makes-differe...
Tilt and trim adjust the angle of the motor and thus the running surface of the boat, ...the grip on the water, the ability to jump on plane and many other operations ... be around the base of the ram, or drip down around the power tilt and trim motor. ...Sometimes you can bang on the power tilt and trim motor with the head of a ...

Jan 10, 2016 | Boating

1 Answer

Tilt and trim wont trim up taking off works fine running down the lake


Check trm/tilt release screw,does trim motor run but motor doesn't lift,if trim motor doesn't run then it's probably trim solenoid/relay

Oct 09, 2014 | Boating

1 Answer

Tilt/Trim Motor


check trim switch with multi metre ! check solinoids not stuck !

Jan 16, 2014 | Boating

1 Answer

1978 evinrude will tilt up but not down


Sounds like something is wrong with your tilt and trim motor. You can find some replacements below.

http://www.iboats.com/Evinrude-Power-Tilt-and-Trim-Motors/dm/view_id.269667

Apr 16, 2013 | Boating

1 Answer

Tilt trim go up wont go down 2003 johnson 140 hp 4 stroke


You may want to check service bulletin #2002-052. Some of these motors supply too much voltage to the trim switch at the throttle lever and that trim switch stops working. There is an add-on harness #586806 that fixes this. If you can still tilt and trim the motor at the trim switch that is built into the motor housing this is likely the problem.

Jan 30, 2012 | Boating

1 Answer

Evinrude 225hp will not power tilt batteries OK manual release will turn but still not able to tilt motor?


Check trim tilt switch (if that's ok ) Try the trim / tilt relay inside the engine cover.
Could also be limit switch above the trim motor up further under the motor.
My bet is switch or relay
Good luck

Aug 14, 2010 | Clymer EvinrudeJohnson Outboard Shop...

1 Answer

How to service a tilt/trim on a 50 hp yamaha outboard. I think the fluid is low as the trim will leak back down after raising the engine.


To check the fluid level, tilt the motor up and engage the tilt lock lever. Open the bolt on top of the tilt/trim reservoir. The fluid should be even with the bottom of the bolt hole. If not add some fluid. When you put the bolt back in, run the trim up and down a few times. That should purge any air out of the system. Always be on the lookout for any leaking hoses or fittings. Hope this helped and best wishes.

Aug 31, 2009 | Boating

1 Answer

I have a 1994 150 hp Yamaha outboard motor with tilt-trim. My motor is stuck in the up tilt position and will not tilt down. It is working when I go up, but not down. I have talked to a used parts dealer...


Stop! Dont replace the pump...I would bet that it is the "down" Solenoid that went haywire. I would begin by replacing the Down solenoid...it is a far easier and cheaper fix and if your pump works to raise the engine then that tells me that it is not faulty. The Down solenoid looks just like a starter solenoid and the one that you are looking to replace has a GREEN wire to it. Yellow with a red stripe is for the starter. Blue wire is the up solenoid. So replace the one with the green wire going to it and I bet it will fix your problem.

Jul 14, 2009 | Boating

Not finding what you are looking for?
Boating Logo

Related Topics:

531 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boating Experts

Steve
Steve

Level 3 Expert

693 Answers

ray gallant

Level 3 Expert

41478 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14584 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...