Question about Fisher DS603W / DS603B / DS603I Dishwasher

1 Answer

Fisher Paykel F1 is blinking on both drawers - how do I resolve this without calling a service tech?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 64 Answers

F1 is a fload code the bottom drawer has to come out and dry up the water make sure the power is off

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F1 error on Fisher and Paykel Dish Drawer


Sorry did not see your problem report earlier. If you have checked the sensor under the bottom drawer and it is dry, then F1 is caused by top drawer power filter fault. This means the bottom drawer controller is giving the F1 error but the top drawer controller has no power. Can you confirm this.

Apr 08, 2013 | Fisher and Paykel 23 in. DD-603SS Built-in...

2 Answers

I have a Fisher and Paykel DD603 which was working well however i ran through some service tests. Whilst doing so i managed to flood the unit. F1 initial came on the lower drawer, then both drawers. Now...


The power filter board at the base of the dishwasher has gone faulty or you may have dislocated a connector on the filter board at the base of the dishwasher. This is the same board that has the flood switch on it.

The connector provides power to the drawers. If this is not the case then the filter board itself will have gone faulty with the water falling on it.

This part can be got from this site. The worst scenario is that you ran the heater on the lower drawer with no water causing the heater fuse to blow. This cuts the power to the drawer controller. This is very expensive to replace as the fuse is integral to the heater. Unfortunately you will not will be able to get rid of the F1 on top drawer until the power to bottom controller is restored.

The reason water spilt out is because you did not have the lid seal on when you ran the wash pump.
Make sure the mains plug is taken out when working on the dishwasher.

Mar 13, 2011 | Fisher and Paykel 23 in. DD603H SS...

1 Answer

The code F1 keeps blinking and I can't shut it off.


f1 means u have a leak on your machine and the water has triggered the flood switch underneath the lower drawer. if u need more help please reply.

Apr 27, 2010 | Fisher and Paykel DD605HSS 23 in. Built-in...

2 Answers

Hi Both drawers show error F1 flashing beeping with rinse light on and both pumps run after power is applied to machine


F1 error indicates flood switch in base has activated, meaning machine has leaked. This causes machine to drain continously, and can only be stopped by switching off power. Not easy to fix if you don't have experience- bottom drawer has to be removed to access flood switch, then machine needs to be test run and checked for leaks. Best to call the professionals!!

Oct 03, 2009 | Fisher and Paykel 23 in. DD603H SS...

3 Answers

Fisher & Paykel M#DD603SS - While not running F1 repair mssg


Actually the part is called a Link Actuator. There is one for the upper drawer and one for the lower. When the drawer is shut, it will actuate and the dishwasher will lift the drawer up against the upper lid. When the actuator is broken, this will trigger the flood switch which inturn triggers the F1 code. In the meantime, when the dishwasher is turned on, the water will shoot over the side walls of the drawer and get down below to damage the terminal block module.

Jun 21, 2009 | Fisher and Paykel DD605SS Stainless Steel...

1 Answer

E-mail for Fisher Paykel DD603 manual


Josh, you will need to have a Tech out to look at it... F/P will not sell you parts to repair it. The F1 indicates that the flood switch has been tripped. There are many possible causes for this but probably the upper drawer link support has broken and is getting stuck between the lid and the drawer in which case you will need a new lid and link support.

May 05, 2009 | Fisher and Paykel 23 in. DD-603 Built-in...

1 Answer

Fisher & Paykel single drawer dishwasher F1 flashing.


F1 indicates a problem with the Flood sensor. I cleaned all the filters etc. removed the drawer viewed under the drawer, it was dry. There is nothing further I can do, so called the Appliances repair person and booked an appointment for him to determine if an outlet hose is blocked or has a hole in it or whatever. Thanks for all the suggestions Blokes. I'm technically challenged. Happy New Year

Dec 28, 2008 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

My fisher pykle dishwasher


F1 is a flood code. There are several reasons this could be happening. One, make sure that you are not putting dishes in that are too tall for the drawer and possibly keeping the lid from closing all the way.
Also, on those models, there is a device behind the drawer that guides the hoses and wiring as you open and close the drawer. On older models, this link support was made of nylon and would crack and break loose over time. Then the broken end gets jammed under the back of the lid the next time it is used.
Since the machine is now "wet" it will not stop doing the F! and you should hear the sound of both drain pumps running. The machine is trying to drain itself and it will not allow any other input. It needs to be serviced. Other techs will give bad advice about "just take out the lower drawer and dry up the flood sensor"
Avoid this advice like the plague. There's a reason it got wet and that needs to be determined. There is a diagnostics procedure to make sure the lid motors are operational. This machine should only be serviced by a properly trained Fisher Paykel tech, as many independent techs fancy themselves as Fisher Paykel techs and they know enough to be dangerous...

Dec 06, 2008 | Fisher and Paykel 24 in. DD603H W Built-in...

1 Answer

Fisher Paykel F1 error / double dishwasher drawer


F1-water on bottom of dishwasher. Uselly it cost by broken drain hose. Need expert tech to fix the problem.

Dec 01, 2008 | Fisher and Paykel 23 in. DD-603SS Built-in...

Not finding what you are looking for?
Fisher DS603W / DS603B / DS603I Dishwasher Logo

Related Topics:

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher Dishwashers Experts

Tony Houde
Tony Houde

Level 2 Expert

64 Answers

isaac johny
isaac johny

Level 3 Expert

796 Answers

noel
noel

Level 3 Expert

4740 Answers

Are you a Fisher Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...