How do I find the control panel that controls the pump motor? Due to error code E23?

[PDF]Error Code E23 Frigidaire Washing Machine - WordPress.com

https://grednandwestsign.files.wordpress.com/.../error-code-e23-frigidair...

E23 Drain pump relay on control board failed or wire off pump. E24 Drain pump relay If your. Frigidaire Washing Machine Error Code is not listed here, check Then the code E41 appeared and. I could do nothing else with the washer. The error .

The E20 error code is a class code that indicates a drain problem in the washer. This is consistent with the drain and spin problem that you are observing. To determine the exact error code, follow these steps:

Wake the machine by pressing any button

Wait 5 seconds

Press and hold the START and PAUSE/CANCEL buttons simultaneously

The exact error code (E21, E23 or E24) will be displayed.

If E23 or E24 are displayed, you will normally need to replace the control board due to a failed drain pump relay.

If the E21 code is displayed, I recommend that you follow these troubleshooting tips:

Check the washer drain to see if it is clogged.

Check the washer drain hose for a clog or restriction.

Make sure that the washer drain system complies with the installation instructions for the washer.

Try to gravity drain the washer by placing the drain hose in a bucket on the floor. If the washer will gravity drain, you may be able to

unplug the washer

and remove the bottom front service panel using the procedure in the image below. Arrange towels to catch residual water that may be in the washer and check the pump filter and drain trap for a clog or debris. If you find no clog or debris, then you may need to replace the drain pump. NOTE: You should not attempt this procedure unless you are completely confident in your technical ability to safely access and check the pump. Do not disassemble the drain pump hose if the washer is full of water.

Hi James, thank you for your post! If you are getting an error code E23, it usually means one of three things: your drain pump relay has failed, a wire may be disconnected from the pump, or your main control board needs replacing. However, since you have already replace the control board, one of the best ways to determine if this is a false error code is to reset the power to the appliance by either unplugging it or flipping off the breaker. It is important to wait roughly ten minutes and then turn the washer on. If the error code persists, it would be advisable to reach out to an expert technician to ensure the appropriate replacement part is ordered and is installed correctly to prevent future issues. I hope this information helps to some degree - thanks for your question, and please do not hesitate to reconnect.

Hello Daniel Ellsworth - Typically error code E23 indicates that the washer has detected that the drain pump relay on board has failed or a wiring communication. Usually this means that a certified technician will need to repair the wiring or in most cases the main control board will need replacing.

This usually indicates

An E23 error code on your Frigidaire Washer indicates a failure of the drain pump relay. Depending upon the model, your washer may be under warranty for up to 25 years, so check your warranty's status before attempting any repairs yourself.

Yor previous diagnostic its right; are you replace the control board... OK (other cases need replace it two times). Are you check the pump relay and wires, and this its OK, good.

Are you check and clean internally the pump and filter? So try cleaning it yourself, it is easy even with basic skill. You will need a star screwdriver, a scare-screw driver, pliers.

Remember, better have the machine empty before doing anything, because you'll be working on the drain line.



Hope this helps.

before buying anythings, you have too check the manual too see if you didn't put it in factory test mode by accident. the manual is suppose to be under the top,(two screws on the back)
After that, second thing you have too do, remove the back (six screws) the drain pump is located under the the baril. there is a black rubber tube attached to it. In this tube, there is a basket that keed hard thing away from the pump. In my case, some hair pin pass the basket and block the pump rotor. The computer of the machine told me it was Error E23 but after cleaning, everything work like new!!

So try cleaning it yourself, it is easy even with basic skill. You will need a star screwdriver, a scare-screw driver, pliers.

Remember, better have the machine empty before doing anything, because you'll be working on the DRAIN LINE.

Hope that help someone.
Vincent D.

before buying anythings, you have too check the manual too see if you didn't put it in factory test mode by accident. the manual is suppose to be under the top,(two screws on the back)
After that, second thing you have too do, remove the back (six screws) the drain pump is located under the the baril. there is a black rubber tube attached to it. In this tube, there is a basket that keed hard thing away from the pump. In my case, some hair pin pass the basket and block the pump rotor. The computer of the machine told me it was Error E23 but after cleaning, everything work like new!!

So try cleaning it yourself, it is easy even with basic skill. You will need a star screwdriver, a scare-screw driver, pliers.

Remember, better have the machine empty before doing anything, because you'll be working on the DRAIN LINE.

Hope that help someone.
Vincent D.

this is a drain pump relay on the control board failure.you either need to replace the wire or the main control board

take toe panel off unit than empty your pump filter...