Question about HP LaserJet 1320 Printer

1 Answer

Laserjet 1320 shows undocumented light pattern, won't respond

When I power up the printer it doesn't go into its initialisation routine - the toner light is off, the attention light in on, and the ready & go lights are flashing. The printer will not respond to any buttons being pushed.

Posted by on

1 Answer

Re: Laserjet 1320 shows undocumented light pattern, won't respond - HP LaserJet 1320 Printer Printers & Copiers

Paper jam

Posted on Nov 20, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Hp laserjet 1320 toner empty?

you might try a recycled cartridge and have a lot less invested.Sounds like your cartridge is empty.Is print quality bad or light?

Mar 20, 2014 | HP LaserJet 1320 Printer

3 Answers

HP 1320 Prints Blank Pages

HP 1320 Prints Blank Pages Problem with the HP LaserJet 1320 Printer

Sep 03, 2011 | HP LaserJet 1320 Printer

1 Answer

HP Laserjet 1320 replaced cartridge, toner light stays on

it may be not a genuine one, or you have a paper jam inside the printer

Mar 25, 2010 | HP LaserJet 1320 Printer

1 Answer

Hello sir.I am Dnyaneshwar,I am using Hp laserjet 1320 printer. when I'll print the page it can't page to print and automatically centre light is started.

Make sure the toner is not empty just remove the toner and shake it and installed it if the problem is continue then replace the toner.
Hope this helps. Please rate my response.
Have a good day.

Mar 23, 2010 | HP LaserJet 1320 Printer

2 Answers

The Attention, Ready, and GO LEDs are on solid

Here is service manual for HP 1160/1320 series ->

Solution is on page 34. I hope it will help you.

Feb 27, 2010 | HP LaserJet 1320 Printer

1 Answer

Printer error


If all the three lights are on, then the issue is with the board (formatter board to be precise). Press the green button to check if there is a difference in the light pattern, the first light pattern is called primary light and after pressing the green button, the format changes to secondary light pattern, please find below the link to check the different light pattern for primary and secondary light pattern.

HP LaserJet 1160 and 1320 Series Printers - Printer Light Patterns (Error Messages)


May 16, 2009 | HP LaserJet 1320n Printer

1 Answer

Hp Laserjet 1320 toner rubs off page

when the toner rubs off means it wasnt fused which means you need to replace the fuser

Feb 27, 2009 | HP LaserJet 1320 Printer

5 Answers

HP Laserjet 1320n Error Lights not in Manual

hi friends......
shivachadra is here.....just i faced this problem "Attention, Ready, and GO LEDs are on solid"
and i got solution in troubleshooting....just vi refixe the connetion of laser scanner........its the error of comunication between laser scanner and formatter....

May 27, 2008 | HP LaserJet 1320 Printer

2 Answers

HP Laserjet 1320 Printer doesn't respond

Manual Feed or Continuable
This state can be reached in
the following circumstances:
● Manual feed
● Out of paper for the
specified tray
● General continuable error
● Memory configuration error
● Personality/Job related

To recover from the error and
print whatever data is possible,
press the GO button.
If the recovery is successful,
the printer goes to the
Processing Data state and
completes the job.
If the recovery is unsuccessful,
the printer returns to the
Continuable Error state.

Feb 05, 2008 | HP LaserJet 1320 Printer

4 Answers

Hp laserjet 1320 problem

This is an error state that is not described at HP site.

Try to do a hard reset:

1) Turn off the printer

2) Press and hold down the green GO button

3) Turn the printer on and continue to hold the green GO button for at least 5 seconds, but not longer than 15 seconds. During the process, the Attention LED will turn on.

4) Release the GO button.NOTE: If both the Attention light and the Ready LEDs turn on before the GO button is released, the cold reset procedure must be started over at step 1.

5) The printer LEDs begin cycling. The cold reset process runs until completion and the printer returns to the Ready state.

Hope it will help you

Jan 24, 2008 | HP LaserJet 1320 Printer

Not finding what you are looking for?
HP LaserJet 1320 Printer Logo

524 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts


Level 3 Expert

94039 Answers


Level 3 Expert

7983 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides