I have a canon 2.1 Mega pixeks but they didn't give the software of the machine .i don,t know how to use it to put the photos into my comper,can you help me?

Section 2-39 thru 2-45 of the user manual will give you a step by step photo presentation of how to load the paper. If you do not have the manual, please send me an email to [email protected] and I will send it to you. Please put "canon LC2050" as the subject.

There are several possible causes for "memory card locked", "memory card error", or "no memory card". The most common cause is having the tiny slide switch on the side of the card in the wrong position. The second most common is trying to use a 4GB or higher SDHC card with an older camera made before SDHC format came out. There are also other common causes if the above didn't help, with troubleshooting steps for this problem listed here. If these don't help, and you do end up having to format your card, see the recovery software, along with the corrupted card procedures in this blog article.

Press Stop/Reset button for 5 seconds.. after your printer will start to process... thanks

Hi............

I didn't get your question........

If you want Driver and software to your printer please click here

Select your operating system and download

I hope this solution will helpful for you
Please don't forget to click on Four thumbs which are given below & then write testimonial for my appreciation if it is helpful
THANKS & Keep Using fixya

Software is available from Babylock.com and the hoops are available from Amazon.com You might want to contact a dealer on line who sells this model. Here is one I found in Austin who sells your machine for 399.00 http://www.sewaustin.com/eblasts/MoreSew-LessDough/MoreSewLessDough.pdfThe dealer might be able to help or contact one in your state via phone.
A fully loaded used model sells for abt. 700.00 so you got a good deal!
A phone call or email is better than having to travel...Shame on Babylock.com for not helping you!
Good Luck and don't give up.

In the same tray as the plain paper. Either replace the plain paper with photo paper or just place the photo paper on top of the plain paper. Don't forget to remove the excess photo paper after you have finished printer photos.

If it has low Mega Pixels it's worth binning if it has high take it to a camera shop to get it looked at. Good Mega Pixels 8 - 14 rubbish mega pixels 2 - 6. hope this helps!

how I get maximum resolution by 5 mp camera with small photo.

my friend mega pixel relates to the print out u want out of ur photo file,on the monitor screen everything looks same if u dont zoom too much ,

for 5X7 print 1 mega pixel photo looks fine and more than enuff if u want a 5X7 print out of it

for 6X8 and 8X10 2 mega pixel is ok and for further enlargements u need higher mega pixel

or if u need output on large LCD screens of like 46 inch and 52 and 60 inch then also u need good resolution pics to display properly other wise pixelation will appear

so how can i help u more in this pls rate me FIXYA for this if u like

http://www.canon.com.au/products/scanners/scanners_low_medium_volume/canoscanlide25.aspx try this should give you what you need

Hello Surs, Wish I could be more confident of this but I couldn?t find much on this series of printer. You didn?t indicate if there were any LED codes being flashed but this is the only reference I could find involving ?6000? and this model printer. Issue: Power light (or Alarm / Power lights) alternate(s) between orange and green 3 times (6000) ________________________________________ Solution: Reset the printer Follow these steps to reset the printer: 1. Turn the printer off with the Power button (if available). 2. Disconnect the data cable from the printer (not applicable to WiFi, Bluetooth or Infrared) . 3. Unplug the printer's power cord for a few seconds, and then plug it back in. If troubleshooting a communication issue, reconnect the data cable (not applicable to WiFi, Bluetooth or Infrared). 4. Turn the printer back on. I don?t have a service manual for this printer nor was I able to find one anywhere. From poking around the Canon site it appears that there are other error codes than what is published in their manual or web site so it might be worth a call to the help desk. Let us know if you have any more questions or information and don?t forget to rate the post.