Question about Hayward Pool & Spa

1 Answer

Going from 230v to 115v on Super Pump

Having trouble moving the plug from the 230v location to the 115v location on our new Hayward 1 Hp Super Pump. Can't find an electrical drawing that shows the exact location for the plug. I keep blowing the circuit.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 93 Answers

Open back you will see the bars to hook to it should show which is the right side 3wire only for 115

Posted on Jul 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changeing 115volt to 230 volt


Most power Flo pumps run above ground pools and run on 115v only.You can look at the wiring diagram on the motor label to see if it is convertible, it will show wiring configurations and amps for both 115v and 230v. If not, it is a 115v motor only.

Sep 11, 2013 | Hayward Power Flo Lx 1 Hp Pool Pump Sp1580

1 Answer

1 1 2 hp pool pump wire


look on side of motor there is a schematic for low and high voltage high voltage from factory

Apr 28, 2013 | Hayward 1 12 Hp Super Swimming Pool Pump...

1 Answer

Hayward super II wiring


move so both terminals are used sometimes they don't line up put on 220 then move to other position

Jul 24, 2012 | Hayward Super Pump 1 1/2 - Hp for In...

1 Answer

My hayward super pump keeps tripping my GFI. The trouble locates to my pump


It could be an overly sensitive GFCI. If you replace it first, because it is cheaper than a motor, then you can determine whether you need a new motor.

I hope this helps.

Sep 11, 2011 | Hayward Super Pump 1 1/2 - Hp for In...

2 Answers

I just installed Hayward 1.5HP inground and it tells me that if i use the 115v to use a 30 amp breaker - and when i left the 230V button positioning inside the back of the pump and connected with a 14 ...


double the amps, 230 runs cooler (my fav) . 1.5 is 9.6 amps at 230 volt. you will need to set the motor to run on on the lower voltage this is why you are having problems.. also the motor is thermally protected . this why it will run for awhile and shot off .. remember to prime the pump after any pump repair !!!! . jay the pool pump repair guy in longwood florida

Jun 05, 2011 | Hayward 1.5hp Pool Pump Motor Motor A O...

1 Answer

The pump comes factory set for 230v. Power to the motor is 115v so I switched the jumper as indicated. The jumper is set on 2 posts with an arrow pointing to 230v. I moved it to 1 post and the arrow now...


CHECK YOUR BREAKER IT MIGHT BE THAT YOU ARE 230V .. IF IT IS A WIDE BREAKER ITS 230 OR IF IT IS A SLIM BREAKER ITS 115V , A VOLT METER IS YOUR BEST FRIEND.. REMEMBER TO VOTE FOR YOUR FAVORITE FIXIT GUY ! THANKS JAY

Jun 29, 2010 | Hayward Super Pump 1 1/2 - Hp for In...

1 Answer

I am replacing my Hayward 1 HP superpump. The old pump had the 230/115 conversion plug on line 1. The new pump has it on line 2. Do I jusst connect the 115 v(hot) wire to line 2? That would be oppisite of...


It will not matter where you put the hot and neautral as long as one goes on line 1 and the other on line 2. Just be sure to reset the voltage indicator to read the 115V like before and your all set.

Oct 19, 2009 | Hayward 1.5hp 230v 2 Speed Uprated Super...

1 Answer

New hayward 1 HP super pump runs 1 or 2 seconds, then shuts off. After 1 or 2 minutes, will come on for 1 or 2 seconds, then shuts off again


Check that the motor is set for the proper voltage. They are usually factory connected for 230V and if you have a 115V line feeding it the motor will overheat and cycle the overload as you describe.

Jul 04, 2009 | Hayward Sp2607x10 Super 1 Hp Swimming Pool...

1 Answer

Switching my hayward pool pump from 230v to 115v. I was told i could just move the jumper, line up the arrows for 115 and be fine but my gfi keeps tripping out?


Setting the pump for 115V wont by itself cause the trip. There is either a ground in the circuit or the GFI is bad. You may want an electrician to test any further than this.

Jul 03, 2009 | Hayward 3/4hp Super Pump Inground Pool...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hayward Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Bill Jordan

Level 2 Expert

372 Answers

john h

Level 3 Expert

10958 Answers

Are you a Hayward Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...