Question about Nintendo Game Boy Advance SP Console

1 Answer

I might have the same problem..

You no when u press the butten to make it bright or not bright or if u wish to have light or not have light.. for some od reason when i click it, it doesnt light up..

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 20 Answers

Maybe the button is broken

Posted on Aug 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

The normal wash cycle keeps flashing, and no other butten you push will change the flashing of the butten. Is there a reset butten, Or can I shut off the power and turn it back on to cycle it. This is on...


Hi

Press and hold the HEATED DRY/NO HEAT DRY/AIR DRY button for 15 seconds to unlock the control lock in your dishwasher. Also make sure that nothing is blocking the drain pump assembly. If the issue returns after its cleaned then it means that the control board has gone bad and should be replaced. Hope this helps...please post back for further assistance.

Daniel

Jul 09, 2011 | Kenmore 24 in. 15079 Built-in Dishwasher

1 Answer

The channel changing buttons do not work


If other butten works it could be a problem in the butten pls remove from the board and check with thw multimeter
normaly sevaral Mega ohm and it become to below 1k ones you press the butten

Aug 27, 2010 | Insignia IS-DVD1001 DVD Recorder/VCR

1 Answer

Where is the butten to turn of the service light on dash


Put the ignition in OFF, press the odometer button, and keep pressing, then turn the ignition to the 2 position (just short of starting the engine). After 10 to 15 seconds of pressing the odometer button, the service light should go off, and reset itself.

May 20, 2010 | 2002 Honda Accord

1 Answer

2002 Accord: where is the butten to turn of the service light o...


1) Put key on the ignition and don't move it. 2) Press down the odometer reset button, and dont let go. 3) Turn the ignition to the #2 position (past the radio detent) and wait like 15 seconds, until the service light goes off.

May 18, 2010 | 2002 Honda Accord

1 Answer

Can't see diplay only see alines and light


do one thing ...put the battary in side phone then press on off butten then after three minut press down side on the phone reset butten press it after three minut remove battary ....then check

Dec 28, 2009 | O2 Xda Orbit Smartphone

1 Answer

How to switch on


there is a butten on the top press it........if there is no butten then...press the red butten on the keypad for while

Nov 14, 2009 | Nokia 6500 Slide Cellular Phone

1 Answer

I press the on butten then it works good for a few minites then the contrast and brightness thing keeps apearing. I keep pulling the plug out then in and solves the problem for another 1 min then the thing...


Its more likely your cables or the monitor itself. Try replacing the cables, or try storing the settings of the monitor once you are happy with the resolution

Oct 17, 2009 | Computers & Internet

2 Answers

Sylvania mp3 model smpk8854


when you turn it on, press the the butten in the bottem right corner. and then press the butten with the little computer monitor and the rench in front of it. press the first butten and then press english.
for any other problem email at rowe20@gmail.com.

Dec 16, 2008 | Audio Players & Recorders

2 Answers

CAN'T PROGRAMORIN TV TOA RCA UNIVERSAL REMOTE


u must press and hold the botton titled as code search until the red light is lit. Once you do so, you program in one of the 3-4 digit codes. I am actually dealing with the same delema. I have an Orion tv except i have no clue what the code for it is. If you could help me out with the code that would be great

Nov 09, 2008 | RCA RCU300WBL Remote Control

1 Answer

Stand by led blink 4 times


when you press the botton the light comes on then goes off

Jul 19, 2008 | Televison & Video

Not finding what you are looking for?
Nintendo Game Boy Advance SP Console Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles & Games Experts

Raj Patel

Level 3 Expert

917 Answers

Julian Wainwright

Level 2 Expert

64 Answers

Zhenya Ogorodnikov

Level 2 Expert

218 Answers

Are you a Nintendo Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...