Question about Ovens

1 Answer

GE MODEL JGBP oven lighting is intermittant. - Ovens

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,136 Answers

Hi, If this is a gas oven, you will need to change the ignitor. This is a very common issue with gas ovens. The ignitor is getting weak and not opening the gas valve as fast as it should.
Please let me know if this helps you or if I can assist you further.


Posted on Jul 11, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


Ge profile oven probe and bake lighs flash intermittently

<P> </P> <P>unscrewed probe housing, insured  black/white wires were secured to connectors and re-installed housing.  ( white wire was not  fully seated into connector Lights no longer flash.<BR></P>,

on Aug 20, 2013 | GE Ovens

1 Answer

Hi, I have a GE Profile oven that needs a light bulb replacement. It is NOT a standard 40W appliance bulb as stated. What bulb is it?

What is the model number for your oven reply with it and i will give you the GE part number for that light bulb

Sep 17, 2011 | GE Profile JTP18 Electric Single Oven

1 Answer

Eror f7 appears and a beeping sound.

An error F7 on this model means there is an issue with the touch-panel. It might need to be replaced even if the error is intermittent. The ERC (an electronic clock controller) might also have issues by can diagnosed further if replacing the touch-panel doesn't completely solve the issue--however, it should.

Feb 28, 2011 | GE JKS05 Electric Single Oven

1 Answer

Ge oven turns off by itself, and sometimes gives

F2 Oven temp exceeds 590 w/ unlocked door High resistance or interference in oven temperature sensor. Replace oven temperature sensor F2
Note: Also see fan thermal switches Indicates that oven is over temperature in one of the following modes within either a cooking or clean mode of operation.
· Control senses oven temperature above 650 degrees F with the door circuit in the unlock mode.
· Control senses oven temperature above 935 degrees F with the door in the locked mode.
· Stalled cooling fan or airflow problem. · Look for welded relay contacts. (Heating elements on in off mode).
· Look for open thermal switch in lock motor circuit. Switch is normally closed and will open if area overheats due to fan not operating. Look for cause - fan thermal switch not closing, fan stalled, etc.
· Look for high resistance in the oven temperature sensor circuit due to high contact resistance (poor terminal crimp, deformed terminals, loose connection) or intermittent solder joint on control or intermittent oven temperature sensor.
· Look for electrical noise interference in the oven temperature sensor circuit (Ham radio, cordless phone, etc.).

Nov 11, 2009 | GE Profile JTP18 Electric Single Oven

1 Answer

We have a GE built in oven, model # JCKP13GP-1. The oven, after operating for an hour or so, shuts down. Sometimes the signal beep goes off when this happens but not always. Any hints on what this could...

We see a symptom like this sometimes due to a failure in the electronic clock/control. Although, by the time we get the control in for repair, it is usually shutting down after a minute or less. You could also have an intermittent temperature sensor or intermittent wiring to it or the door lock, so you should consider that first. The control board for this unit has been discontinued, but we repair them at

Sep 30, 2009 | GE Ovens

1 Answer

Oven wont light

Check the amp draw on the ignitor. If 2.9 amps or less, replace the ignitor. If 2.9 amps or more, replace the gas safety valve.

Aug 02, 2009 | GE Ovens

3 Answers

GE self cleaning radiant oven - model JB578GP

I went out to my circuit breakers and turned the circuit off, let the oven cool, and powered it back up after about 2 hours. Fine now.

Feb 17, 2008 | GE Profile JT912 Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts


Level 3 Expert

83951 Answers

Sal De

Level 3 Expert

2699 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides