Question about Radio Shack Radio Communications

Open Question

How how do i program my realistic pro 2010.. i enter two numbers and then i can not enter a third ..whats up , i did it once and then this happened, thanks

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
BillB-SA
  • 2761 Answers

SOURCE: how do i program my realistic pro-2025 scanner

PROGRAMMING CHANNELS

1. Turn on your scanner by turning the volume clockwise.

2. The scanner might start scanning. If so, press MANUAL to stop the
scanning.

3. Enter the channel number that you want to program and press MANUAL.

4. Enter a frequency including the decimal point. The decimal point shows
up on the display as a -- (dash).

5. Press Enter to store the frequency.

6. To confirm the proper entry, press REVIEW. The programmed frequency
appears on the display one digit at a time.

7. To program more channels repeat steps 3-4.


Posted on Dec 01, 2009

Ad
  • 2 Answers

SOURCE: Realistic

Any radio shack should still sell the base antenna for this. It is cat. no. 20-176. You will need coaxial cable, antenna, (2) pl-259 connectors with UG176 adapter and a pl259 to RCA Motorola adapter.

Posted on Sep 23, 2010

Ironfist109
  • 3018 Answers

SOURCE: help programing a realistic pro

  • Hi, here is the users manual http://www.racingelectronics.com/files/bc80manual.pdf Page 14 tells you how to program your scanner. You have to throw at least one frequency in the scanner before it will receive anything. I can get you some for your area with a state and city.

  • As for programming follow these steps.
  1. Press the manual button.
  2. Now pick what channel you will enter a frequency on by pressing on the number key pad.
  3. Now press the manual button again
  4. Now enter the frequency you want to program.
  5. Now press the "E" button to enter it.
  6. That's it, do it again until your scanner is full.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thanks for using FixYa.

Regards, Tony

Posted on Sep 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i program realistic pro-59 scanner


http://support.radioshack.com/support_electronics/8567.htm

don't know what you will pickup. Nearly all law enforcement, ems, fire have gone to digital trunked systems that are encoded. The above link has a link to the operating manual. You will need to know the frequency of whatever you are wanting to listen to.

Aug 28, 2016 | Radio Communications

1 Answer

My realistic pro-2009 scanner will not stop in the scan mode on an active fequency it just keeps scanning even when I have suelch al the way down


I'm trying to program a Realistic Pro. 2009 and every time I hit program then the frequency and push enter it just keeps saying error can any body help me with this problem???

Jun 03, 2012 | Radio Communications

1 Answer

Help programing a realistic pro 2010 scanner


  • Hi, here is the users manual http://www.racingelectronics.com/files/bc80manual.pdf Page 14 tells you how to program your scanner. You have to throw at least one frequency in the scanner before it will receive anything. I can get you some for your area with a state and city.

  • As for programming follow these steps.
  1. Press the manual button.
  2. Now pick what channel you will enter a frequency on by pressing on the number key pad.
  3. Now press the manual button again
  4. Now enter the frequency you want to program.
  5. Now press the "E" button to enter it.
  6. That's it, do it again until your scanner is full.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thanks for using FixYa.

Regards, Tony

Sep 19, 2011 | Uniden BC80XLT Handheld Scanner

1 Answer

How to program freqencies on pro 2020 20 channel realistic


Wow, that's a real oldie -- circa 1981. To program it:
1. Power the scanner ON.
2. Press MANUAL .
3. Select the channel that you wish to program. You can do this by repeatedly pressing the MANUAL key, or enter the desired channel (01 - 20) followed by the MANUAL key.
4. Press PROGRAM.
5. Enter the desired frequeny, including the decimal point (e.g., 156.55).
6. Presto ENTER.
7. To program more frequencies, press PROGRAM and then repeat steps 2 through 6.

Follow this link for more operating instructions:

http://support.radioshack.com/support_electronics/doc45/45530.htm

For a comprehensive database of active frequencies in your area, visit:

www.RadioReference.com

Bill B.
Listening in since the 60's

Oct 23, 2010 | Radio Shack Pro-2052 Scanner

3 Answers

I have a realistic pro-2021 scanner and dont know how to operate it other than turning it on or off can you help ??


Programming Frequencies

1. Select the desired channel.

2. Press [PROGRAM] to enter the programming mode.

3. Enter the desired frequency.

4. Press [ENTER].

Selecting the Channel

Step 1:

1. Press [MANUAL]. Continue pressing until the display shows
Channel 20. Press [PROGRAM].

2. Press [2][0][MANUAL]. Press [PROGRAM]. (or press [PROGRAM],
press [2][0], press [PROGRAM]).

Step 2:

Press the keys (example 162.55)

Step 3:

Press [ENTER]. To program the next frequency, move to another channel in
this way. Press [PROGRAM] to advance to the next channel. Repeat the
same steps to add more frequencies.


SKIPPING BANKS

1. Turn the power on.

2. Press the number key that corresponds to the bank to be skipped.

3. The corresponding bank number indicator disappears from the display
and the entire bank is skipped.

NOTE: To restore the banks, press the number key again.


SEARCHING WITH YOUR PRO-2021

To search for transmission, press [PROGRAM], enter limits of frequency
range, and press [up arrow] or [down arrow] to activate "search."

1. Press [PROGRAM].

2. Press [LIMIT].

3. Enter the lower limit of frequency range to be searched.

4. Press [ENTER].

5. Press [LIMIT].

6. Enter the upper limit of frequency range to be searched.

7. Press [ENTER].

Activate "search" by pressing [up arrow] or [down arrow]. [Down arrow]
starts search from the highest frequency and goes down. [Up arrow] moves
in the opposite direction.

Press [SPEED] to accelerate or to slow down the search.

Jan 07, 2010 | Radio Shack Pro-2096 Base Scanner

3 Answers

How do i program my realistic pro-2025 scanner


PROGRAMMING CHANNELS

1. Turn on your scanner by turning the volume clockwise.

2. The scanner might start scanning. If so, press MANUAL to stop the
scanning.

3. Enter the channel number that you want to program and press MANUAL.

4. Enter a frequency including the decimal point. The decimal point shows
up on the display as a -- (dash).

5. Press Enter to store the frequency.

6. To confirm the proper entry, press REVIEW. The programmed frequency
appears on the display one digit at a time.

7. To program more channels repeat steps 3-4.


Jun 03, 2009 | Radio Communications

3 Answers

Wanted manual realistic 2010scanner


The realistic 2000 series scanners do not have a "VFO" (variable frequency occilator) in the true meaning of the sence. This basicly means that they can only scan the channels or memories that you have programmed.

You can however set a low frequency (like 144 Mhz) and a high frequency (like 145 Mhz) and the scanner will "bounce" between the two, picking up anything in between.

Do you have the operating manual? If not, here is a copy

Turn on your Pro-2010 by rotating [VOLUME] clockwise. (When first turned on, your Pro-2010 may start scanning).
Rotate [SQUELCH] fully counterclockwise. You'll hear a rushing noise from the speaker. Slowly rotate [SQUELCH] clockwise until the noise just stops.
You're now ready to start entering frequencies.

Programming Frequencies
Before programming frequencies, make sure your Pro-2010 is turned on and the SQUELCH is adjusted.
Suppose you want to program Channel 1 to receive 162.55 MHz. Here's how you would do it:

1. Press [MANUAL] and select channel 1. You can do this in two ways:
press [MANUAL] continuously until the Display indicates Channel 1 or
by pressing [1] [MANUAL].

2. Press [PROGRAM] to enter the programming mode.

3. Enter the desired frequency. In this case, press the [1] [6] [2] [.]
[5] [5] keys. Check the display to make sure the frequency it shows
is the one you meant to program. If it is, press the [ENTER] key.

4. To add more frequencies, just press [PROGRAM] to advance to the next
channel and follow the steps above.

5. If you ever want to change the frequency entered for a specific
channel, just enter the new frequency "over" the old frequency using
steps 1, 2, and 3.

Make a mistake while entering the frequency? Just press [CLEAR], enter the correct frequency and press [ENTER]. If you're entering a new frequency in place of an old one, the old frequency won't be "erased" when you press [CLEAR]. It will remain stored on that channel until you correctly enter a
new frequency and press [ENTER].

You'll hear a "peep" sound as you press the various keys. This lets you know the key has been properly "entered" into your Pro-2010.

Using the Scanning Function
Your Pro-2010 will automatically scan all the channels you've programmed and stop whenever it finds a signal. To scan channels, just press the [SCAN] key.
To stop scanning, just press [MANUAL] and you can select specific channels
you want to listen to.

IMPORTANT! Your Pro-2010 won't scan unless SQUELCH is set to the point where no sound is heard if a signal isn't being received.

Delay Function
When your Pro-2010 is scanning, it will stop whenever it finds a signal on a channel. As soon as the signal ends, the scanning function will resume. Most communications heard will be two-way. To make sure you don't miss any replies, press [DELAY]. This will cause your Pro-2010 to stay on a channel for two seconds after the end of a transmission, giving you time to hear any reply. To release the Delay function, just press [DELAY] again. The Delay indicator will show on the display when the Delay function is used.

Lockout Function
You may want your Pro-2010 to "skip over" certain frequencies while it's scanning (such as continuously transmitted weather broadcasts). To "lock out" such channels, follow these steps:
1. Press [MANUAL] to stop scanning. Continue to press [MANUAL] to
advance to the channel you want to lock out.

2. When you reach the channel, press [LOCK OUT]. The display will show
[o] to indicate this channel will be skipped over during scanning.

3. To release the lockout, press [MANUAL] to stop scanning. Advance to
the channel that is locked out and press [LOCK OUT] once again. [o]
will disappear from the display.

If you use the lockout function on all channels, scanning will be impossible - you'll only be able to change channels using [MANUAL].

Speed Selection
Your Pro-2010 will normally scan channels at a rate of four channels per second. If you press [SPEED], channels will be scanned at a rate of nine per second. Press [SPEED] again to return to a rate of four channels per second.

Priority Function
You might want to scan other channels yet not miss a call on a channel of particular interest to you (police, fire, ambulance, etc.). The Priority function will let you scan other channels - but if a call is received on the Priority channel, your Pro-2010 will automatically switch to the
Priority channel!

1. Only Channel 1 can be used as Priority Channel: Key in the desired
Priority frequency into Channel 1.

2. Priority function works only when the unit is in Scan or Manual mode.

3. Press [PRIORITY] to start Priority function. A [P] will appear on the
display.

4. Press [MANUAL] or [SCAN] to listen to other channels. Your Pro-2020
will check the Priority channel and switch to it if a signal is
received on it.

5. To cancel Priority function, press [PRIORITY] again. the [P] will
disappear from the display.

SEARCHING WITH YOUR PRO-2010
One great feature of your Pro-2010 is its ability to "search" for frequencies being used. This means you can hear all the action on the airwaves in your area! To use this great feature, just follow these steps:
1. Press [PROGRAM] key.

2. Press [LIMIT] key. Enter the lower limit of frequency range to be
searched (such as 45.00 MHz). Press [ENTER].

3. Press [LIMIT] key again. Enter the upper limit of frequency range to
be searched (such as 46.00 MHz). Press [ENTER].

4. Press either [up arrow] or [down arrow] to start Search. [Down arrow]
will start search from the highest frequency and go down. [Up arrow]
will start from the lowest frequency and go up.

5. You can control the speed of the search by using the [SPEED] key to
accelerate or to slow down the search.

6. Search will stop when a frequency is found with a signal. To restart search, press [up arrow] or [down arrow]. In Program Mode, search range will be displayed each time [LIMIT] is pressed. It is impossible to change the lower frequency only: to change lower frequency you must change higher frequency first. The higher frequency can be changed any time.

Storing Frequencies
If you want to enter some of the frequencies found during search, do this:
1. Press [MONITOR] when your Pro-2010 finds a frequency you want to store.

2. Use [MANUAL] key to select a channel to enter the frequency your Pro-
2010 found. The display will show the frequency currently stored on
the channel, but don't worry - the old frequency will be erased when
you start to enter the new one.

3. Press [PROGRAM].

4. Press [MONITOR] again. The new frequency found during the search will
be displayed.

5. Press [ENTER] to put the new frequency into the channel in place of
the old frequency.

6. Press either [up arrow] or [down arrow] to resume the search. To
return to manual or program operation, press [MANUAL] or [PROGRAM].
To resume the search from one of the limit frequencies, press [LIMIT]
and then [up arrow] or [down arrow].

Error Indications
Sometimes when you try to enter a frequency for a channel or as a search range limit, you may find an ------ on the display. This means the frequency is in error and you won't be able to enter it into your Pro-2010. Such frequency errors usually mean you've entered a frequency outside the ranges your Pro-2010 operates on (such as 225.00 MHz) or you've put the decimal point in the wrong place (14.682 MHz instead of 146.82 MHz). Check carefully to find your mistake and then press [CLEAR]. You can now enter the correct frequency.

Hope this helps,
M3ODQ

Feb 01, 2009 | Radio Communications

1 Answer

Realistic pro 2010 scanner


to program
turn on unit, press program button, key in frequency ###.### press enter. keep advancing thru the channels with the program button until finished

Jun 24, 2008 | Audio Players & Recorders

1 Answer

Apex Digital GB4308 remote


Programming the Remote Control Remote-control switchover Press VCR/DVD, SAT/CABLE or AUX to select the device you want to control. To program the remote control Press and hold VCR.DVD, SAT/CABLE or AUX for over 2 seconds until the LED on the remote control turns off. Release the button the LED will light again (the remote control enters the PROGRAMMING mode). Enter three-digit code number for your equipment. If the correct code number is entered, the LED blinks three times. If you enter a code not listed below, or you press any other buttons than SEARCH and 100+, the LED turns off. To search codes Press ad hold VCR/DVD,SAT/CABLE or AUX for over 2 seconds unil the LED turns off. Release the button (the LED wil light again) and the remote control enters the PROGRAMMING mode. Press SEARCH. Press CH+/- to search codes downwards or upwards. Each time you press CH+/-, the code number decreases or increases by 1 while the remote control sends the code number for POWER button on your device. If the desired code number is found,press 100+ to program the code for your device until the LED blinks three times.Then the remote control exits from the PROGRAMMING mode and returns to norml operation. Or press any other button to exit from the PROGRAMMING mode after the LED blinks rapidly eight times, and the operation is not active. To check the current code number Press and hold VCR/DVD, SAT/CABLE or AUX for over 2 seconds until the LED turns off. Release the button (the LED will light again) and the remote control enters the PROGRAMMING mode. Press 100+ . You may read the code numder according to the LED display status as follows. * If there is no operation within 20 seconds during the steps mentioned above, the remote control will automatically exit from the appropriate operation. Code Number First - digit 0 1 0 1 Second - digit 0 0 4 5 Third - digit 0 6 3 0 First - digit Blinks rapidly once Blinks once Blinks rapidly once Bliks once Secod - digit Blinks rapidly once Blinks rapidly once Blinks four times Bliks five times Third - digit Blinks rapidly once Blinks six times Blinks three times Bliks rapidly once

Jan 05, 2007 | Apex Digital GB4308 43" Rear Projection...

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radio Shack Radio Communications Experts

john milligan

Level 3 Expert

514 Answers

Steve

Level 3 Expert

3289 Answers

xxxxxx xxx

Level 3 Expert

4981 Answers

Are you a Radio Shack Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...