Question about Canon PIXMA MP150 All-In-One InkJet Printer

1 Answer

MP 190 Error Message E 2 2 after paper can't get it to work again

My MP190 is less than a 6 months old and worked great until I got a paper jam. I removed the paper, it came out easily, not tears, the full sheet of paper was removed. Now my printer keeps flashing an error message E 2 2. I have taken out the ink cartridges and reloaded, looked in vain for paper shreads. But nothing. I have even uninstalled it and then reinstalled. No good. Is there anything that I can do or is it a goner?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello everyone...its just a simple problem....dun worry...1st, u hve to connect ur printer to other computer(not the same pc as u're using now)...then the printer will work fine...after tht..connect ur cable back to the previous computer(1st computer)...then ur printer will be fined!!!!!!!!!!! :) -darkrogue

Posted on Jan 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My daugher is using Canon MP190, and there is a blink error message E3, which according to the online manual, it is due to a paper jam. We checked, and there is no paper left in the printer, but the error...


Hello, Welcome to FixYa!

E3 error is mostly because of paper jam. their may be small bit paper jam in side
There are some "micro-sensors" that detect a paper jam. There will be tiny piece of paper, or a lump of dust, inside those sensors, thus "tripping" the sensor and saying you paper jam.

To solve it
Open printer cover and check to make sure no paper or foreign objects obstructing the printer feeder

If you become sure that now really there is no paper, dust or foreign objects then
Turn the printer off, and disconnect the AC power-cable. Open the printer cover & now give the printer a "blow-job" by compressed air.
If still problem exist then best & final option is to just contact to any Canon service provider

Anymore help regarding the issue, I am here to help
Thank you for using FixYa!
Concerned: Angel Bird

Apr 10, 2011 | Canon PIXMA MP190 All-In-One InkJet...

1 Answer

How can fix the problem with my canon mp 190


That error is telling you that the ink absorber inside is full. You need a shop to replace that because you need to use Canon diagnostics to reset the error code.

Jul 21, 2009 | Canon PIXMA MP190 All-In-One InkJet...

1 Answer

One sheet of paper is jammed in my printer canon pixma MP 190. What is your advice?


As with the majority of printers you should be able to open it by lifting the top on hinges or a panel in the back to gain access to the internals. After doing this if you can get a hold of the paper you have to very slowly work it out, use two hands if possible it should work free just be careful not to rip it. Also take a look in you manual it may have a trouble shooting section that can also be useful. Hope this helps.

Jul 12, 2009 | Canon PIXMA MP190 All-In-One InkJet...

1 Answer

Canon MX860 Rear Paper Jam


I have a small piece of paper jammed in my Canon MX-860 that Cannot be seen from anywhere. Can you help me find so I can clear it

Jun 27, 2009 | Canon Office Equipment & Supplies

1 Answer

Paper jam


try to add some paper to the tray ..maybe the paper pick mechanism has been failed..

May 17, 2009 | Canon Office Equipment & Supplies

3 Answers

Need help with my printer canon MP190


I refilled my MP190 Black cartridge PG-37 by drilling a hole in the top (roughly in the middle) and using the syringe supplied with the ink refill kit. To make the printer work again, press and hold down the Stop/Reset button (on bottom right hand side of printer) for at least 5 seconds until the display reads 1 again. This bypasses the ink level detector and is explained in the trouble shooting section of the on screen manual supplied on the printer installation CD. It works. It then happened again with the colour cartridge, so I repeated the process. It worked again. This should also work for the PG40 and CL41 cartridges.

Apr 20, 2009 | Canon PIXMA MP190 All-In-One InkJet...

21 Answers

Canon pixma mp190 error code e4


My canon mp190 gives E3 paperjam error but there is no paperjam, how do i fix it?

Jan 09, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Epson aculaser cx11nf MP E paper jam


open the mp tray
locate 2 white plastic egg shaped piece on the ends of the steel rod
gently push one or the other towards the back of the machine
if the paper jam error message is on then the roller will turn as soon as you give it a push
re load the paper
open and close door a or e
printing should resume
that white piece works with the paper lift to get the paper up to the in feed roller

Sep 01, 2008 | Epson ACULASER CX11NF All-In-One Printer

Not finding what you are looking for?
Canon PIXMA MP150 All-In-One InkJet Printer Logo

1,072 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2178 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...