Question about HP OfficeJet 6210 All-In-One InkJet Printer

2 Answers

Error messae appearin as soon as I turn it on

Error reads: Error:0xc0620004411:lib_micci2.c

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 4,402 Answers
Re: Error messae appearin as soon as I turn it on

Use the instructions below to resolve the issue by restarting the product.

  1. Disconnect the Universal Serial Bus (USB) cable from the back of the product, but leave the product turned on.
  2. Open the cover of the product and remove the print cartridges.
  3. Close the cover and wait for the Insert Ink Cartridges message to display.
  4. Disconnect the power cord from the back of the product and wait for one minute.
  5. Reconnect the power cord. If the product does not automatically turn on, press the Power button.
  6. Open the cover and reinsert the print cartridges.
  7. Close the cover. If prompted, print a calibration page.
  8. Reconnect the USB cable, and try to print a print job from the computer.
If these steps did not resolve the issue, contact HP technical support for assistance

Posted on Jan 10, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Error messae appearin as soon as I turn it on

ебануться...нихуя не помогло.

Posted on Sep 10, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to fix OXC1AB0003 error on the P PhotoSmart 2575

Remove the cartridges and do a full reset without them in by removing the wall socket and re-plugging.

More information has been answered in another thread.
Error oxc1ab0003730 Lib micci2 tango

Apr 07, 2015 | HP PhotoSmart 2575 / 2575v / 2575xi InkJet...

1 Answer

My samsung ml-1610 series printer's software is installed but the printer is not installed

my oj 7310 all in one is give me error mesege 0xc0620004 411:lib-micci2.c

Nov 03, 2009 | Samsung ML 1610 Laser Printer

1 Answer

Hp 2355 all in one error message


open the rear access door and clean the rollers with a cloth, dam it with little water and unplug the machine and press and hold the ON button for 1 min and release the button and plug in the power cord, it should resolve the issue.

Regards,  raj_p5983 

Jan 21, 2009 | HP OfficeJet 7310 All-In-One InkJet...

1 Answer

Alarm = check printer 5100

This error means that there is something obstructing the printing process. Check inside your printer through the gears that you can see under the lid. There should be something obstructing the gears such as dirt or even some paper caught underneath the rollers that you have to jiggle around to even see. Check very thoroughly..

Hope this helps

Chris (ziraffa)

Jan 05, 2009 | Canon PIXMA MX300 All-in-One Printer

1 Answer

Error Code 0xc0620004411:lib_micci2.c

reinstall your driver and also check usb connection cable.

Jan 03, 2009 | HP PSC 1610 All-In-One InkJet Printer

1 Answer

0XC0620004411:lib_micci2.c error on PSC1610

Try doing power drain.

By Isolating printer from power and computer.
Press and hold power button for 5 sec.
Then try turning on. without connecting to the computer.

Sep 04, 2008 | HP PSC 1610v All-in-One Printer

2 Answers

Hp 2355 all in one error message

reset to factory defaults, also check the whole printer for paper jams. A paper jam can often casue smaller pieces to get stuck in gears or rollers. The message about opening and closing the lid is how the printer knows you went in to check it and closeing it triggers it to try again. If thers still a jam it will keep giving the message. The fist jam was caused by something, check and make sure there isnt any pieces of plastic broken off inside. If it has a rear access panel, check there also.

Feb 16, 2008 | HP PSC 2355 All-In-One InkJet Printer

2 Answers

Error: 0x07a74dd61959:lib-barracu

Its a Fimware Error.
Try a Hardware Reset.
-Switch the Printer on
-unplug the powerkable
-press "#" and "6" and plug in the Powerkable.
when the Display shows Initialising or Semi-Full-Reset. release the "#" and the"6".

sometime this is working

Jul 14, 2007 | HP OfficeJet 6210 All-In-One InkJet...

Not finding what you are looking for?
HP OfficeJet 6210 All-In-One InkJet Printer Logo

Related Topics:

393 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts


Level 3 Expert

94198 Answers


Level 3 Expert

7983 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides