How do you drain the water? - LG LP1200DXR Portable Air Conditioner

If your refrigerator is not displaying power, but you can hear the water drain pump running, the issue may be related to the water drain assembly. Here are a few steps you can try to replace the water drain assembly:

1. Unplug the refrigerator from the power source.
2. Locate the water drain assembly. It is typically located at the bottom of the refrigerator near the back.
3. Drain any remaining water from the assembly by disconnecting the drain hose.
4. Remove the old water drain assembly by unscrewing or unclipping it from the refrigerator.
5. Install the new water drain assembly by reversing the steps used to remove the old one.
6. Reconnect the drain hose and plug the refrigerator back in.

It is important to refer to the manufacturer's manual for specific instructions on how to replace the water drain assembly on your refrigerator, as the process may vary depending on the model and design.
It is also important to note that this may not solve the problem of no power display, it might be related to other electronic or electrical issues, like a blown fuse or a malfunctioning control board. It's better to contact a professional technician to diagnose and fix the issue.

Anytime a cycle is interrupted and a new cycle is selected, the dishwasher will start by draining water first. This is so any water that was accidentally spilled while loading the dishwasher is drained or in your case, water that was left over from the last cycle. When draining problems occur, the dishwasher will drain some water but not all. The timer only allows about 60 seconds for water to discharge. It will not accommodate for a clog.

The most common reason why a dishwasher wont completely drain water is a clog at the end of the discharge hose where the disposal and hose meet. If this should happen, clear the clog and replace entire
hose. A clog can happen inside the dishwasher as well.

Anon, Make sure gas or breaker(power) is turned off to the Heater so it will not come on during draining,connect a hose onto bottom valve of water heater, run hose to a floor drain and insert, turn your water main off so as not to fill tank while draining, open water heater drain valve, water will then drain from attached hose into floor drain until empty. For water to run faster you may open a near by hot water tap, this will allow air into tank as you drain it, do not forget to turn this tap off before refilling tank. You then can turn main back on for a bit if you would like to do a flush of sediment from the bottom of tank.
See links below for more instruction and video.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Drain Water Heater Today Homeowner

How to drain water heater

http://www.bobvila.com/articles/how-to-drain-a-water-heater/#.VxqJ6NQrJxA

Copy following link.
http://waterheatertimer.org/Water-heater-will-not-drain.html

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Two things to consider....clean water or dirty water?

Clean water usually indicates the fill valve is not shutting off all the way and the fill valve is "weeping" water in all the time = new fill valve time!!

Dirty water usually is not a dishwasher problem but more of a plumbing issue. Often the sink drain that carries the sinks water outside is not fast enough and some of this sink water is backing up into the drain hose and filling up the dishwasher through the drain hose. The drain from the sink to outside needs attention as this type of a problem indicates a slow house drain for that sink.

The dishwasher drain line should be clamped to the top underneath part of the counter before entering the sink drain plumbing, this may help the water from coming back inside the dishwasher.

Two things to consider....clean water or dirty water?

Clean water usually indicates the fill valve is not shutting off all the way and the fill valve is "weeping" water in all the time = new fill valve time!!

Dirty water usually is not a dishwasher problem but more of a plumbing issue. Often the sink drain that carries the sinks water outside is not fast enough and some of this sink water is backing up into the drain hose and filling up the dishwasher through the drain hose. The drain from the sink to outside needs attention as this type of a problem indicates a slow house drain for that sink.

The dishwasher drain line should be clamped to the top underneath part of the counter before entering the sink drain plumbing, this may help the water from coming back inside the dishwasher.

Two things to consider....clean water or dirty water?

Clean water usually indicates the fill valve is not shutting off all the way and the fill valve is "weeping" water in all the time = new fill valve time!!

Dirty water usually is not a dishwasher problem but more of a plumbing issue. Often the sink drain that carries the sinks water outside is not fast enough and some of this sink water is backing up into the drain hose and filling up the dishwasher through the drain hose. The drain from the sink to outside needs attention as this type of a problem indicates a slow house drain for that sink.

The dishwasher drain line should be clamped to the top underneath part of the counter before entering the sink drain plumbing, this may help the water from coming back inside the dishwasher.

check the water make sure the water is correct. fill water drain water and circulation water.
fill water comes from under sink, drain water from drain pump and drain hose ,circulation pump controls the water washing. let me know if this helps.

1. Drain the cooling system. Refer to Draining and Filling Cooling System (LS4 Static Fill) Draining and Filling Cooling System (LZE, LZ4, LZ9 Static Fill) Draining and Filling Cooling System (9C1, 9C3 Static Fill) Draining and Filling Cooling System (LS4 GE 47716 Fill) Draining and Filling Cooling System (LZE, LZ4, LZ9, 9C1, 9C3 GE 4771 Fill).
2. Loosen the water pump pulley bolts.
3. Remove the drive belt.
4. Remove the water pump pulley bolts and pulley.
5. Remove the water pump bolts.
6. Remove the water pump and gasket.
7. Clean the water pump mating surfaces
   1. Position a NEW water pump gasket and the water pump to the engine front cover. Notice: Refer to Fastener Notice.
   2. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.) .

1. Install the water pump pulley and bolts.
2. Install the drive belt.
3. Tighten the water pump pulley bolts. Tighten the bolts to 25 Nm (18 ft. lbs.) .
4. Fill the cooling system. Refer to Draining and Filling Cooling System (LS4 Static Fill) Draining and Filling Cooling System (LZE, LZ4, LZ9 Static Fill) Draining and Filling Cooling System (9C1, 9C3 Static Fill) Draining and Filling Cooling System (LS4 GE 47716 Fill) Draining and Filling Cooling System (LZE, LZ4, LZ9, 9C1, 9C3 GE 4771 Fill).
5. Inspect for leaks.

Hope this helps

If you clear the drain, the water will not fill up again. (try hot, but not boiling, water, forced into the drain hole with a turkey baster) When drain is clear, water will run into the drain pan located near the compressor. The fan will cause that water to evaporate.