Question about Printers & Copiers

1 Answer

Copier won't cycle after warm up.

Toner Light stays "on", won't allow the copier to cycle.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Master
  • 1,346 Answers
Re: Copier won't cycle after warm up.

1- you did not say what machine this is for, kind of hard to help if we don't have enough info.

2- this is probably for a fax/printer/copier
they have a closed toner unit that you replace
If you replaced it ( assuming you did because the TONER light is on, and it will not copy as long as it does not detect a new cartridge) the new one is most likely defective or depending on your model it may require to to be reset in the menu.
Good luck

Posted on Nov 16, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Replaced Konica 7022 toner and add toner light stays on

Remove the toner bottle carefully, pwr off and unplug the machine , then plug it in and turn it on do not put toner bottle into machine until asked for.

Jun 30, 2009 | Konica Minolta Printers & Copiers

1 Answer

My AL 1631 cycles on, light comes on but won't move or copy

Toner is running low. Light come on to say the machine is adding toner. Soon it will come on and stay on.

Jun 08, 2009 | Sharp AL-1655CS Copier

1 Answer

No error message but copier light doesn't come or number of copies doesn't work

let it run eventually the toner lite will come on, sharp copiers will run an extended period trying to add toner to the developer. developer is 70% iron filings and 30% toner as it uses the toner it cycles more in to stay at the proper level.

Apr 14, 2009 | Printers & Copiers

1 Answer

It will not copy after I emptied the waste container.

There really isn't enough information given to give a proper solution. This copier has the drum light come on steady or flashing to indicate the waste toner needs to be removed. I don't know if you're a technician or not but lay people have emptied the toner cartridge instead of removing the drum, removing the cap on top of the drum, emptying the waste toner , replacing the cap on the drum, then putting the drum back into the copier. I've never had a copier keep the drum light on after doing this.

Let me know if you need more help.

Nov 18, 2008 | Canon NP 7130 Black and White Copier

1 Answer

Konica Minolta Copiers

F26 Toner density adjustment problem. This means machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel that you should disconnect the toner motor first. This ??? ?????? happens probably because either machine wasn't set up properly, or the customer kept on using the machine with the toner light on.

Aug 22, 2008 | Konica Minolta Printers & Copiers

3 Answers

Xerox XD100 copier

occasionally on that model it will run continuously looking for toner when it has actually run check the toner, it does not always indicate toner required

Jan 20, 2008 | Kyocera RI-3530 Black and White Copier

1 Answer

Toner low signal

Try turning your copier off & back on. Allow the machine to cycle after turning it back on - until it comes to ready or displays add toner signal again. You can try this three or four times as it sometimes takes the machine a few trys to advance the new toner to the toner sensor. If after 4 attempts you are still getting the add toner message - you may have a dirty or faulty toner sensor. The toner sensor is located inside the developing unit that you are loading toner into. Toner sensor is usually located on the bottom of the developing assembly & is held in by 2 scews. It can be cleaned with a dry cotton rag & reinstalled. 90% of the time power cycling the copier a few times will solve this problem.

Apr 18, 2007 | Sharp AL-1000 Copier

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts


Level 3 Expert

93802 Answers

old marine
old marine

Level 3 Expert

1294 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides