Question about Philips Magnavox 51MP392H Rear Projection Television

3 Answers

51mp392h/17 I have a rainbow at top and bottom of screen. What can I replace to fix the problem?

Posted by on

  • 2 more comments 
  • Anonymous Dec 27, 2007

    they my convergan board is bad..

  • TNTONE Dec 31, 2007

    HAVE RED OUT OF ALIGNMENT BOW ON TOP AND BOTTOM OF SCREEN

  • mtnmaninwv Jan 01, 2008

    my tv is doin the same thing and is no more than 3 years old

  • scottrock68 Feb 05, 2008

    Rainbow in picture,top middle left,bottom.

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 74 Answers

The STK392-120 convergence IC's are defective and need to be replaced. There may be smaller components that also need replacing as well such as resistors to the IC's.

Posted on Mar 08, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same tv,not three years old.Sounds like a defect!!

Posted on Feb 05, 2008

Ad

HAVE RED BOW . BLUE IS GOOD . RED I CANT AJUST JOESTV2003@YAHOO.COM

Posted on Nov 16, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LG 700e crt monitor is showing all in rainbows!!!!


Remove any speakers or magnets that you might have near the monitor as they can cause visual distortion on your monitor screen.

Mar 05, 2014 | LG Studioworks 700S 17" CRT Monitor

2 Answers

I need an outer screen for my TV Magnavox(51MP392H/17). Where can I purchase another screen?


No,not changeable,the screen about 90% of the tv.The new screen part if tv companies sell it to u.The part and labors will exeed the new tv.Not worth repair if screen broken or damages with noticable when tv is on.

Jan 16, 2010 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

Maganavox 51mp392h/17 double objects at top and bottom of screen.


You need to replace your convergene ICs. It's best to call a repairman for this job.

Aug 09, 2009 | Philips Televison & Video

1 Answer

Philips 51MP392H/17 PJTV. Green beam pulsating horizontally.


Most likely problem is the ACS panel if you have already changed the ICs and resistors.

Apr 06, 2009 | Televison & Video

1 Answer

I have a Magnovox HD TV Progressive Scan (Floor Model) TV


You can find a replacement Philips/Magnavox fresnel screen, in stock, for this model (51MP392H/17) at this following link from a major parts distributor:

Philips / Magnavox 51MP392H Replacement Part Fresnel Screen

And here's a link for the Lenticular (middle) Screen, if needed:

Philips / Magnavox 51MP392H Replacement Part Lenticular Screen

Jan 16, 2009 | Philips Magnavox 9P6034C 60" Rear...

1 Answer

Philips rear projection tv-wont turn on


Sounds like your Convergence chips failed, were your red/blue/green colors slowly seperating or was the picture starting to curve on the top or bottom or both? if so see below general post.
Also what model # is your TV and what size?

51MP392H/17
Actually I have this TV and you need 2 Convergence IC's STK392-120's (120's and 150's will work) of course order 2 of the same type I'm using replacement 150's they allow for a little higher heat and were cheaper ALSO you need to replace the 12 resistors with 6.8 ohm metal film resistors, make sure they are metal film! don’t skimp out here I did and then they blew and fried my IC's and I had to replace everything again!

Great reference link that I posted pictures on, check out page 3
http://www.techlore.com/forum/thread/16736/Magnavox-51MP392H-17-51-quot--TV-has-double-vision/

Where I got all my parts that worked:
Suburban Electronics http://www.suburban-elect.com/

Manual Library you should find all you need here:
http://www.techlore.com/group/2/list_downloads



What you need:
(2) STK392-120 OR STK392-150 IC chips
(12) 6.8 Ohm Metal Film resistors
set of star screw drivers
15 watt pencil solder pencil, DO NOT use a high watt iron you will fry the surface mounted item.
good leaded solder, and flux


BTW if you don’t plan on trying this and are going to throw out the TV, I still need a IC convergence board for a 51MP392H/17 TV I'm fixing, I'm willing to pay S/H and buy your IC board that’s not been tampered with. Edwinkraus@hotmail.com

Nov 02, 2008 | Philips Magnavox 51MP392H Rear Projection...

3 Answers

Magnavox MDL 51mp3964h distorted and waved picutre


Hello pkrocks

It looks like your convergence amplifiers have gone bad, this is a common problem. If your set uses the STK329-110 or STK329-xxx series of amplifier both of them will have to be replaced. There is a lot of information on fixya about how to do this yourself, but you have to be careful in removing and replacing the amplifiers and the associated bias resistors.

I hope this helps

Thank you,

Shuttle83

Sep 15, 2008 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

Rain bows


Hello keriro74,

Your convergence amplifiers ICs have become defective, They will have to be changed out. They are usually marked with a STK392-110. You will have to also change out the fusable links connected to the STK392-110. Desolder the pins and unscrew the ICs and remove both of them. Then desolder the fusable liks and replace them with the new ones, then insert the new ICs and solder them in (being careful not to create solder bridges). Then you will have to perform the convergence on your TV, Try to use Auto-Convergence to do this.

I hope this helps

Thank you

Shuttle83

Sep 09, 2008 | Philips Magnavox 51MP392H Rear Projection...

2 Answers

Magnavox 51mp392H/17


Yes,semiconductors is the term used to describe transistors,diodes,intergrated circuits(IC's)etc...the correct generic part# for that model is STK392-120 which is an intergrated circuit (IC)which in that TV works as a convergence amplifier.The specific Philips part# is 932212344682. There are two of them you need to change both. Also check the two 6.8 ohm resistors nearby if they are burnt or discolored.

Sep 16, 2007 | Philips Magnavox 51MP392H Rear Projection...

Not finding what you are looking for?
Philips Magnavox 51MP392H Rear Projection Television Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75178 Answers

matt martin
matt martin

Level 3 Expert

1213 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...