Question about Invacare Pronto M51 Power Wheelchair

Open Question

What invacare programming tool number is used to program invacare m51power chair

I need to reprogram my invacare pronto m51power chair what is the invacare programming tool number

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: where is the reset button on a invacare m51

The controller puts out fault codes though the LEDs. Count them and then look in the operators manual for likely causes. In my experience it is the electronic brakes that fail on these units and they are costly.

Posted on Oct 16, 2009

Ad
  • 5 Answers

SOURCE: Invacare Pronto M51wheelchair just stopped;

I believe that indicates a left motor fault

Posted on Oct 16, 2009

wcdoc1953
  • 278 Answers

SOURCE: How do i know when my invacare pronto m5 is fully

With an M51, a full charge will be indicated by all three joystick indicator lights lit- red yellow green. The green far right LED is the full charge light. Also the charger has indicator lights that go from red/yellow to full green at full charge. Hope this helps

Posted on Oct 24, 2010

wcdoc1953
  • 278 Answers

SOURCE: I NEED A WIRING SCENATIC FOR AN INVACARE PRONTO m6

I assume you need a wiring schematic for an M61. The circuit board schematics are proprietary and not available. The component schematics and interconnects for switches and wiring harnesses are available, as are the parts diagrams and drawings. Please clarify your specific need and issue.

Posted on Oct 24, 2010

wcdoc1953
  • 278 Answers

SOURCE: i have invacare pronto m51 with surestep the spjis

The 9 flash error code indicates a communications fault. The communication fault relates to the communication between the joystick and the control module. The joystick on the arm mount is connected to the control module in the base. When there is a break in the wiring of this wiring harness, also called a bus cable, a fault occurs. This trips the computer and the computer sends out a flash code to the joystick. Simply stated there is a broken or pinched wire between the joystick and controller. Look physically at the wire and check for cuts, breaks or pinches. The best short term repair is to repair the broken wire with solder and heat shrink or tape. You can also use **** splice connectors and tape. The best long term repair is to replace the harness with a part available from Invacare. The most definitive way to diagnose this problem is to read the fault log of the controller using a hand held programmer available to dealers and certified technicians. The number and type of fault codes logged in the controller is another indicator of which
component(s) has failed. Hope this helps.

Posted on Nov 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reprogram my invacare pronto m51power chair


You will need to contact a service tech in your area to do this. They should have a special programmer box that can adjust the settings on the chair to improve the chairs performance.

May 02, 2015 | Invacare Pronto M51 Power Wheelchair

1 Answer

I would like to know how toadmust the sencitivity on the wobble stick


You have to have a Invacare Remote Programmer to plug into the joystick and program different sensitivity levels. Sorry, there is no other way to adjust the joystick. Find a store that sells Invacare chairs and see if they can program your joystick. The programmers are expensive to buy and without training with one you could easily cause your chair to really drive bad to not drive at all.

Aug 29, 2014 | Electric Mobility Pronto M41 Power Chair...

1 Answer

My son has a invacare chair should go 6 mph but has slowed to a snails crawl. How Can I speed it back up?


The chair may be in what they call SLOW MODE or the batteries are weak. If you have powered seating on the chair the seat has sensors that make the chair drive slow or not drive at all when the seat is tilted or reclined or raised. A sensor can go bad or get out of position. The joystick could have different programming for different drive modes. Try changing drive modes.

Jun 11, 2014 | Invacare Supply Group Pronto M61 Standard...

1 Answer

How do I reset m51 Prono power chair


There is no reset button on a M51. It only has fuses. If it is turning on and it has blinking lights or if you have a joystick that has a display that says Press Reset then the chair needs to have an external reset plugged into it or the chair may need to programmed or serviced.

May 20, 2014 | Invacare Pronto M51 Power Wheelchair

1 Answer

How do I turn off the pronto m41 speed limiter


Hello,

The Pronto M41 does not have a speed limiter per say. If the chair used to go faster than it does now then you may have some kind of problem with the chair. If the chair has always driven' slow, that is slower than the maximum 3.5 to 4 MPH then a Invacare Remote programmer is needed to program the chair to go it's full speed.
Seek a Invacare dealer and ask them if they can check the programming.

May 16, 2014 | Electric Mobility Invacare Pronto M41...

1 Answer

The chair rolls about 6" after releasing the drive stick


have a tech with programer to reprogram the brake stopping distance and u will be ok

Jan 17, 2014 | Electric Mobility Invacare Pronto M41...

1 Answer

Rebuilt motor installed in Pronto m50 power chair, now joystick forward, takes chair to right, joystick right takes chair forward, joystick to left, taks chair back, joystick back takes chair left, HELP


u need a programer o reset that joystick to the new motor,so call the dealer have them send out a qualified tech with a programer to check error codes and reprogram

Sep 26, 2013 | Health & Beauty

1 Answer

How do we lock out the fast speed on grandpa's chair so he doesn't hurt anyone?


Ann You will have to contact the provider of Gramp's chair to ask if they have a programmer for Invacare chairs. Then they will have to program the chair for a lower speed. Of course you can turn the speed down on the joystick but Grandpa is probably the one that will put it back to fast cause its going too slow. try also contacting Roadrunner Mobility@ 1-800-467-2668 and ask if they have a tech in your area that has a progeammer to slow his chair down. Hope this helps

Mar 31, 2011 | Invacare Supply Group Invacare Pronto M91...

3 Answers

One red light three green flash when turned on


Your chair has a motor problem. The code does not tell which side it is. Make sure both motors have the brakes in the drive position before turning on the chair. Also check that both motors are plugged into the main control module in the base of the chair.

May 15, 2010 | Invacare Supply Group Invacare Pronto M91...

Not finding what you are looking for?
Invacare Pronto M51 Power Wheelchair Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Invacare Health & Beauty Experts

wcdoc1953
wcdoc1953

Level 2 Expert

278 Answers

Colin Taylor

Level 2 Expert

346 Answers

MobilityRepairSpecia...
MobilityRepairSpecia...

Level 1 Expert

61 Answers

Are you an Invacare Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...