Question about Blueant Supertooth 3

Open Question

I am trying to hook up my hands free to my new phone the phone finds it no problem but when I try to pair it my phone shows pairing rejected by ST3

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Pair

Hi Cass. I had to same problem as I was used to using the original version. You need to hold the On button for 6 seconds, then follow the prompts. Go to the following website for the manual. Good luck !!
http://www.blueant.com.au/manuals/s3/S3_manual.pdf

Posted on Apr 01, 2009

Ad
  • 3230 Answers

SOURCE: where do i find my blue ant password?

Hi there,

password for any Bluetooth headset is 0000.
try this...


Good Luck!!

Thanks

Posted on Jul 17, 2009

  • 6 Answers

SOURCE: need to pair my blueant supertooth st3 .

Code is 0000 make sure you press the green button to turn on the blue tooth light on the Blue Ant, while you enter the pin (don't hold it down, just make sure it's on before you finish entering it).

Posted on Aug 18, 2009

  • 2 Answers

SOURCE: ST3 will not pair to any phone. Phones recognizes

I had similar problem with Motorola and Blackberry Perl. It seems that the device may have been used or demoed at the store, and had to be re-set to factory defaults. The procedure is simple.

  1. Make sure that the device is OFF
  2. Press and hold Volume UP and green ON buttom at the same time
  3. After reset, power the device OFF and wait for approximately 10 seconds
  4. Power the device ON, select a language, and follow voice prompts to complete pairing

Posted on Sep 29, 2009

  • 1 Answer

SOURCE: Having trouble pairing phone with Blue Ant ST3

  1. If the Supertooth 3 is on, turn it off by holding down the green Multi-Function button for about 5 seconds (until you hear a voice announce "BlueAnt ST3 powering down").
  2. Hold down "Vol " and the green Multi-Function button until you hear a loud siren/distinctive tone.
  3. The Supertooth 3 will turn on. Hold down the green Multi-Function button for about 5 seconds to turn it off again.
  4. The Supertooth 3 has now been reset: all pairing and other information has been deleted. When you turn the Supertooth 3 back on again it will prompt you to select a language and then go into pairing mode.
You will now need to re-pair your phone with your Supertooth 3.

Posted on Aug 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have recently got a Samsung Galaxy S I9000 and when I try to connect to my blueant st3 a message comes back that the blusant rejects the pairing with the phone. I used to use the bluseant with a nokia...


Darrell 12/11/2010. make sure you have the phone set to sync then press green button on ST3 until it ask what language you require keep it pressed until it states on the screen that you want to sync press ok and you will find that it has connected. You can use the same system to sync it to an I Phone as well

Nov 06, 2010 | Blueant Blue Ant 091193 Supertooth II...

1 Answer

How do I restore factory settings on my BlueAnt ST3. I have a new Blackberry and every time I try to pair them the Blackberry comes up with 'Unable to pair with BlueAnt ST3. Try again?' and every time I...


Here is how I got my Samsung to pair (on page 12 of the Blue ant manual):

Deleting all Paired Devices & Phonebook entries:
1. Ensure the SUPERTOOTH 3 is switched OFF, press
& hold the Volume Up (8) Button.
2. Whilst holding down the Volume Up (8) Button, press
the MFB (1) for 1 second or until a distinctive melody
is heard through the speaker, the software version will
then be announced. Once this occurs, please switch the
SUPERTOOTH 3 off for a minimum of 10 seconds.
All paired devices & phonebook entries have now
been erased.

Go back in and pair your phone, use pass code 0000 and let it reload your address book and you should be good to go

Sep 29, 2010 | Computers & Internet

1 Answer

Cannot pair blueant ST3 wih Nokia 6300


Hi,
Reste the ST3 and then pairi again. It worked for me. Check this link:

http://www.myblueant.com/knowledgebase/reset/st3.php
Deven

Dec 25, 2009 | Blueant Blue Ant 091193 Supertooth II...

3 Answers

ST3 will not pair to any phone. Phones recognizes St3 but will not pair


I had similar problem with Motorola and Blackberry Perl. It seems that the device may have been used or demoed at the store, and had to be re-set to factory defaults. The procedure is simple.
  1. Make sure that the device is OFF
  2. Press and hold Volume UP and green ON buttom at the same time
  3. After reset, power the device OFF and wait for approximately 10 seconds
  4. Power the device ON, select a language, and follow voice prompts to complete pairing

Sep 06, 2009 | Blueant Blue Ant 091193 Supertooth II...

6 Answers

Blue Ant ST3 will not recognize 0000 passcode.


  1. If the Supertooth 3 is on, turn it off by holding down the green Multi-Function button for about 5 seconds (until you hear a voice announce "BlueAnt ST3 powering down").
  2. Hold down "Vol +" and the green Multi-Function button until you hear a loud siren/distinctive tone.
  3. The Supertooth 3 will turn on. Hold down the green Multi-Function button for about 5 seconds to turn it off again.
  4. The Supertooth 3 has now been reset: all pairing and other information has been deleted. When you turn the Supertooth 3 back on again it will prompt you to select a language and then go into pairing mode.
You will now need to re-pair your phone with your Supertooth 3.

Jun 11, 2009 | Blueant Blue Ant 091193 Supertooth II...

3 Answers

My g3 iphone says blue ant st3 password incorrect but it's the only one they give you...won't connect with my phone


Hi - I had the same problem setting up my 3G S. Here's the solution. In "Settings/General" set the Bluetooth to "ON". Turn your ST3 OFF by holding the green button until she says it's Powering Down. Now press and hold the green button ON until Language Selection (British English) option. Select language by pressing green button again. Next she will say "Device Found-Paring Successful-Enter password 0000". Enter 0000 and your phonebook will start downloading. There ya go!

Jun 07, 2009 | Blueant Blue Ant 091193 Supertooth II...

1 Answer

The phone won't pair up with the blueant st3


Go to this page, it will answer any question concerning the blueant .. including pairing to your phone .. activating your blueant etc http://www.blueant.com.au/index.phpalso gives you step by step instructions on codes, pairing etc

May 27, 2009 | Nokia N95 Cellular Phone

1 Answer

Pair


Hi Cass. I had to same problem as I was used to using the original version. You need to hold the On button for 6 seconds, then follow the prompts. Go to the following website for the manual. Good luck !!
http://www.blueant.com.au/manuals/s3/S3_manual.pdf

Jan 15, 2009 | Blueant Blue Ant 091193 Supertooth II...

Not finding what you are looking for?
Blueant Supertooth 3 Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blueant Cell Phones Experts

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

William Alequin

Level 3 Expert

928 Answers

Are you a Blueant Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...