Question about Stanley Powerlock Tape Measures 33212 1/2 in x 12 ft

1 Answer

Fix stanley powerlock tape - Stanley Powerlock Tape Measures 33212 1/2 in x 12 ft

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Stanley Master
  • 42,042 Answers

Cheaper to junk it and get a new one.

Posted on Apr 30, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't figure out how to add new blades. I can't find anything on Stanley website.


if this a tape measure, then pull the old tape all the way out.
hold the spring end, unhook the tape and put the new tape onto the spring end. Let it wind back up

Mar 27, 2015 | Stanley Measuring Tools & Sensors

2 Answers

How to repair a Stanley powerlock 16 measuring tape ?


From the the attached photo I see that you have completely disassemble the tape. This makes the tape almost impossible to reassemble. The spring has to be back wound fully, the blade attached and retracted back into the case using the back wound spring. This requires special equipment that is not overly complicated, however not possible to make for a once off use. I have designed, built and trained operators to use this type of equipment in a production situation, however in my 35 years of experience I have never been seen anyone back wind a spring by hand. Sorry to say but the tape is ready for the trash.

Mar 21, 2015 | Stanley Measuring Tools & Sensors

1 Answer

Hi. My Stanley IntelliTape 0-77-008 has an 'error'


Mine did the same thing. To fix it I extended the tape all the way out. As I retracted the tape it started working. Try it and let me know if this worked for you.

Jul 17, 2011 | Measuring Tools & Sensors

1 Answer

I have a 12' stanley powerlock series 33-212. I want to replace the blade but can't get it open to start


You don't need to open it to replace the blade. You pull the blade all the way out and you will see that it is hooked to a spring. All you have to do is unhook the old blade and connect the new one and slowly let it wind back in. Remember to hang on tight to the spring so it doesn't snap back in before you get the new blade connected. If you do need to take it apart, there should be screws holding it together.

Dec 11, 2010 | Stanley Hand Tools

1 Answer

How to replace the tape on a stanley 25" tape measure


Did it break and go flying up inside there? Take it back where you bought it, tell them you want a new one, they will replace it, all Stanley tools are warranted, the dealer may not want to do it, but he has to. You will never get it right by replacing the blade. I take that back, you might get it right.

Mar 04, 2010 | Stanley Leverlock Tape Measure, 10'

1 Answer

I have a Stanley Powerlock 25 ft. tape that broken at the 6 ft, mark where do i do to get if fix


those are garuanteed for life,as long as it was product defect.I take mine to local hardware store for replacement.Been 5 yrs. since I bought one.

Feb 10, 2010 | Measuring Tools & Sensors

1 Answer

Install tape


Pull it all the way out ... have a nail ready to put into the hole just past the end on the tape, in the spring. Remove the tape. Install the new one (insert the tang into the hole and twist). Remove the nail and carefully allow the spring to pull the new tape in.

I hope this works for you

Oct 17, 2009 | ACE Stanley& Pocket Powerlock Tape Rule

1 Answer

I have a Stanley 12 ft. Powerlock tape model # 33-212. The plastic thumb locking trigger just broke. Can I purchase a new one and if so where?


No. You'll have to replace the tape measure, or find another similar model to rob the part from...See here and here.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Jul 21, 2009 | Stanley Tools/Goldblatt Tool No.30 - 506...

1 Answer

Adress needed


United States

Canada
Stanley Tools
1000 Stanley Drive
Concord, NC 28027
Attn: Quality Assurance

Stanley Canada
1170 Invicta Drive
Oakville, Ontario L6H 6G1
Attn: Quality Assurance

Feb 23, 2009 | Farberware Stanley Power Return Tape...

1 Answer

Need info on teturning tapes under warrenty


stanley tapes are life time warranty take it back where you bought it they should replace it.

Feb 23, 2009 | Farberware Stanley Power Return Tape...

Not finding what you are looking for?
Stanley Powerlock Tape Measures 33212 1/2 in x 12 ft Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Lawrence Oravetz

Level 3 Expert

9587 Answers

Steve

Level 3 Expert

3287 Answers

john h

Level 3 Expert

12104 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...