Question about Maytag Bravos MTW6600T Top Load Washer

1 Answer

Skips wash and rinse cycle

Machine fills and then empties without agitating or rinsing.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Maytag Master
  • 5,323 Answers

Washer fills with water then drains:
My advice is free because God is so good!
The critical question is. Is the water is just running down the drain but the pump isn't running. If it is being pumped out, and you can hear the pump running just the same as when it's emptying prior to spin then it could be aborting the wash because it is, or it thinks it's overheating. ( due to defective water temperature switch)

If the pump is failing to shut off then there is something wrong with the electronics. If your washer is a mechanical timer controlled device then you may have a sticking switch (which may explain if switching cycles does something for you). But if you have an electronic timer then you may be experiencing a board failure, where a cycle is being commanded when it is not intended to by design.


If water isn't being pumped out, but just draining away all the time, the washer will keep detecting there isn't enough water inside and top up with more.
Modern washing machines should be sophisticated enough to realize something's wrong and abort with an error, but if not, it may continue washing or rinsing for a short while before losing enough water to trigger more coming in again. It can get stuck on this cycle indefinitely and it's called siphoning.
Siphoning occurs when the end of the drain hose is lower than the level of the water inside the washing machine.
Try raising the hose and see what happens.
Also the drain hose should have some type of air gap where it fits into the stand pipe. It should not have an air tight fit.

Again Either it's siphoning down the drain due to an issue with the plumbing, it's overfilling, or also if it ( THE WATER) overheats then in some machines the software will employ a fill and drain tactic to cool down the water. The important thing is to work out which of these different faults is causing the problem by careful observation.


Other switch's to check would be the water inlet valve and the water pressure switch with a multi meter for continuity or OHMS.

Posted on Apr 29, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Roper washing machine does not fill for rinse cycle. Goes directly to rinse agitate without water.


Without Model number I am only guessing but I suspect you have a blocked sensing tube that travels from the Level selector switch to the side of the tub somewhere. It is possible for this plastic tube to become partially clogged and not allow trapped air to vent when tub is drained of water. Usually this problem manifests itself as an overflow of the tub. Check the full length of this clear hose and see if the end nearest the tub looks like it may have debris or dirty detergent clogging it.

This hose is pushed onto a nipple mounted to a reservoir on the side of the tub. Push a thin copper wire 4-5 inches into the those after removing from nipple and also down into the nipple an inch or two before reinstalling the hose to the nipple. You MIGHT even blow into the hose while you have it off and you SHOULD hear a clicking sound coming from the level selector switch body.

Good Luck. Come back with Model number under lid if that doesn't help.

Nov 28, 2015 | Roper Washing Machines

1 Answer

Why does not agitate on rinse cycle


It shouldn't agitate on rinse cycle. ''Quick wash'' is the last type of ''cycle'' you can select that the machine will ''agitate.'' On ''rinse'' cycle, it will fill with water and then simply drain & spin.

May 18, 2015 | Washing Machines

1 Answer

No agitation on extra rinse cycle on Maytag Washing Machine MAV8557AWW


The manufacturer may have found there was little or no advantage to having agitation in the second rinse cycle so omitted it.

Jan 08, 2014 | Maytag Ensignia MAV2757AWW Top Load Washer

1 Answer

Ariston L63S dishwasher does not rinse


Check the screen and the inlet to the pump in the bottom of the washer if it does not empty the water from the wash cycle completely it may not go to the rinse cycle.

Sep 06, 2017 | Ariston Technologies Dishwashers

1 Answer

Please describe a typical washing cycle to me on the RTW4440XQ Roper 3.1 Cu. Ft. Top-Load Washer, please.


The typical cycle is;
fills to selected water level
agitates wash cycle
drains wash water
spins wash cycle
fills to selected water level on rinse cycle
agitates on rinse cycle
drains rinse water
spins final time
end of cycle

Aug 08, 2011 | Roper Washing Machines

1 Answer

GE Top Load Washing Machine -- Agitator will not cycle


Agitator's don't spin on wash cycle.

I would suggest washing the clothes without soap until they rinse clear. If you have hard water, the soap will not easily rinse out of clothes, or off of you when you use soap to wash or shower.

Reduce the amount of soap you use in each wash if this is the case. It sounds like your washing machine is working right.

Jan 26, 2009 | GE WBSR3140DW Top Load Washer

2 Answers

Machine fills and agitates, but won't drain


Please empty your machine and run the machine empty. If the washer goes through the whole cycle without any clothes. Please let me know

Jan 19, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

No agitation in ge hydrowave rinse cycles


you must unplug the washer for just 1 minute open and close the lid 10 times and plug it back in and put it on a light load cycle and let it wash with empty load. shoul work fine after that

Dec 01, 2007 | Washing Machines

Not finding what you are looking for?
Maytag Bravos MTW6600T Top Load Washer Logo

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...