Question about Garden

1 Answer

Is the switch on the park brake normaly open or closed

After a short out of the wireing. i have replaced all the burnt wires,. the moter sraets, but dies when i relese rhe park brake

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 1,727 Answers

Check the seat switch

it doesn't think you're their... it should be normally closed, brake applied its open. when you release the brake if the seat switch isn't open ( you in it ) it'll die

make and model would REALLY help here

Posted on Apr 28, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 merc grandmarkee wont go into park wont start will start if you wiggle in nutral


Park neutral safety switch could be bad , also the shift interlock safety system .
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.
Condition Possible Source Action
  • Shift Interlock System Does Not Release or Lock Properly
  • Circuitry open/shorted.
  • Blown fuse.
  • Damaged stoplight switch.
  • Damaged shift lock actuator.
  • GO to Pinpoint Test A .

PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE OR LOCK PROPERLY A1 CHECK ELECTRON IGN FUSE
  • Check Fuse 5 (5A) located in fuse junction panel.
Is fuse OK?
Yes No GO to A3 . GO to A2 . A2 CHECK FOR SHORT TO GROUND
  • Turn ignition switch OFF.
  • Remove Fuse 5 (5A).
  • Disconnect shift-lock actuator connector C203 located to the right of steering column.
  • Measure resistance of the Circuit 1003 (GY/Y) between the correct terminal of Fuse 5 (5A) and ground.
Is resistance greater than 10,000 ohms?
Yes No REPLACE Fuse 5 (5A). GO to A3 . SERVICE Circuit 1003 (GY/Y) wire between fuse junction panel and shift-lock actuator. A3 CHECK POWER SUPPLY FROM FUSE 5 (5A)
  • Reinstall Fuse 5 (5A).
  • Turn ignition switch to RUN.
  • Measure voltage on Circuit 1003 (GY/Y) wire and ground.
Is voltage greater than 10 volts?
Yes No GO to A4 . SERVICE Circuit 1003 (GY/Y) wire between interior fuse panel and shift-lock actuator. A4 CHECK POWER SUPPLY FROM FUSE 28 (15A)
  • Turn ignition switch OFF.
  • Disconnect connector C2016.
  • Turn ignition switch ON.
  • Measure voltage on Circuit 10 (LG/R) and ground.
Is voltage B+?
Yes No GO to A5 . SERVICE Circuit 10 (LG/R) for open. RESTORE vehicle and RETEST system. A5 CHECK WIRE BETWEEN STOPLIGHT SWITCH AND SHIFT-LOCK ACTUATOR
  • Turn ignition switch OFF.
  • Disconnect shift-lock actuator connector C203.
  • Apply brake pedal.
  • Measure voltage on Circuit 810 (R/LG) wire and ground.
Is voltage greater than 10 volts with brake pedal applied and less than 1 volt with brake pedal released?
Yes No GO to A6 . SERVICE Circuit 810 (R/LG) wire between stoplight switch and shift-lock actuator. A6 CHECK SHIFT-LOCK ACTUATOR GROUND
  • Measure resistance of Circuit 57 (BK) and ground.
Is resistance less than 5 ohms?
Yes No REPLACE shift-lock actuator. SERVICE BK wire.

Mar 30, 2017 | Cars & Trucks

Tip

Automatic trasmission lever is stuck in park position


When this happens, usually it is because of a failure in the gearshift selector switch solenoid.
The gearshift selector solenoid is the switch that unlock the lever from park position when driver turns on the ignition and release brake pedal.
When brake pedal is depressed with selector in park position, this energizes the solenoid, unlocking the shifter.
Teh solenoid is energised by same circuit connecting the brake lights.
When for some reason (a short for example) the brake light fuse that protects the circuit blows, this will result in a failure to energize the solenoid, and lever won't be released from park position.
You find the fuse in the fuse box, on Discovery this is fuse number 1. This is a 15 Amps blue fuse. Fuse is located in the fascia fuse panel.
In most cases you fix the problem by replacing the brake light fuse.

Another reason for a failure to energize the solenoid is a faulty brake light switch.
This means the solenoid itself is faulty and need to be replaced.

How to proceed:

Check brake lights. If brake lights are not working, check and replace fuse number one in the fuse box. This will solve the problem in most cases.

If fuse keeps blowing there must be a short in the brake lights wiring.
You will need to access the rear light access panels and unplug the wiring harnesses that connects to the tail light assemblies.
Replace the fuse and try again to start the car, with all tail lights harnesses disconnected. If it starts drive the vehicle to the nearest mechanic, the vehicle will not be safe without tail and brake lights.

When fuse is not blowing check the brake light switch. Remove the panel above the brake pedal. There you find several switches, the second from the bottom will be the brake light switch. Unplug the switch connector, put parking brake on, turn on ignition and short the two green wired pins.
You should hear a click, while shorting the contacts move the shifter out of park position

When brake light are working fine, and lever stays on park position, it is usually the solenoid or its connections that are faulty. Try connecting directly the solenoid to power. The solenoid is connected to red and black wires. Apply 12 Volts across the wires, following polarity. If this worked the solenoid will click, and you will be able to move the gear out of parkposition. When there is no click you need to replace the faulty solenoid that is located in the shifter assembly.

on Aug 26, 2008 | 1998 Land Rover Discovery

1 Answer

WINDOWS CLOSES BUT OPENS BY ITSELF AGAIN


the switch has a short or one of your wires is shorting, remove door panel inspect the wire's for burnt areas and depending on the vehicle replace the swich.

Oct 10, 2013 | Vehicle Parts & Accessories

2 Answers

I have 1995 jeep wrangler and have no brake lights the tail light fuse is not bad and I changed the brake switch is there another fuse or relay for brake lights


its a brake fuse not the tail park lights.
got trailer wiring hacks on car/ (look)

there are 2 lamps, lamps short.
put in one new lamp, does it work?
y/n
if no , and the new brake lamp switch as 12v on both sides key on and brake pedal reset then the wires are open.
if the voltage reads way low not 12v this line is grounding out.

this is easy to do with and DMM for say $20 , sold at walfart too.

Oct 08, 2013 | 1995 Jeep Wrangler

1 Answer

Chevy cavalier - rear brake lights don't work. The center rear brake light does work as well as all other lights. Replaced the bulbs and fuse - no luck. From what I have been told, the turn signal...


Stop Lamp Circuit Description
The STOP HAZ fuse in the IP junction block supplies battery positive voltage to the normally open stop lamp switch. When the driver presses the brake pedal, the switch contacts close and battery positive voltage is supplied to the center mounted stop lamp (CHMSL) and both left and right stop lamp assemblies. The left stop lamp is grounded at G304 and the right stop lamp is grounded at G304.

Check the ground ! Testing an not guessing is the way to find the problem . Do you know how to test automotive electrical systems an circuits using a DVOM - digital volt ohm meter ? How to use an read a wiring diagram to pin point testing areas in a wiring harness ?
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
How to Use Multimeter to Troubleshoot Common Problems
Mastering Voltage Drop Testing with Pete Meier and Jerry Truglia

Stop Lamps Inoperative
Step
Action
Yes
No

2
Inspect the 20 Amp STOP HAZ fuse.
Is the STOP HAZ fuse open?
YES - Go to Step 11
NO - Go to Step 3
3
Use a test lamp in order to backprobe connector C1 of the brake switch connector between terminal A and ground. Refer to Circuit Testing in Wiring Systems.
Does the test lamp light?
YES - Go to Step 4
NO - Go to Step 5
4
With the brake switch closed, Test for positive battery voltage at terminal B of connector C1. Refer to Circuit Testing in Wiring Systems.
Is voltage present?
YES - Go to Step 6
NO - Go to Step 7
5
Repair the open or short to ground in the Fuse Output-Battery between the fuse block and the brake switch. Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
YES - System OK
--
6
Use a test lamp in order to backprobe the turn/hazard headlamp switch assembly connector C2 terminal A and ground.
Depress the brake pedal.
Does the test lamp light?
YES - Go to Step 8
NO - Go to Step 9
7
Inspect the adjustment of the brake switch. If the adjustment is correct, replace the brake switch.
Is the repair complete?
YES - System OK
--
8
Replace the turn/hazard headlamp switch assembly.
Is the repair complete?
System OK
--
9
Repair the open in Stop Lamp Switch Output between the brake switch and the turn/hazard headlamp switch assembly. Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
System OK
--
10
With brake switch open test terminal A of the brake switch for continuity to ground. Refer to Circuit Testing in Wiring Systems.
Is ground present?
YES - Go to Step 11
NO - Go to Step 12
11
Repair short to ground in Fuse Output-Battery Circuit. Refer to Wiring Repairs in Wiring Systems.
Is repair complete?
System OK
--
12
Test the Stop Lamp Switch Output Circuit for continuity to ground. Refer to Circuit Testing in Wiring Systems.
Is ground present?
YES - Go to Step 13
NO - Go to Step 14
13
Repair short to ground in the Stop Lamp Switch Output Circuit. Refer to Wiring Repairs in Wiring Systems.
Is repair complete?
System OK
--
14
Test terminals F,G,B and C on the Hazard Warning Switch for continuity to ground. Refer to Circuit Testing in Wiring Systems.
Is ground present?
Go to Step 15
--
15
Repair short to ground in suspect CKT. Refer to Wiring Repairs in Wiring Systems.
Is repair complete?
System OK
--


Jul 03, 2017 | 2000 Chevrolet Cavalier

1 Answer

2000 ford focus keeps blowing fuse #54 for brakes, door open light is on unless you push brakes, blower moter fan only blows on 4, when fuse blows cannot take out of park unless we use the manual release...


The blower motors problem is the resistor has gone bad. Sorry I don't know exactly where yours is, But I think it is under the hood , passenger side ,against the firewall, next to the blower. It will have three or four big wires going to it. On the brake I would replace the switch, sounds as if it shorted and check the wires , see if they have melted. The switch is on the brake pedal under the dash. Let me know
Randy

Dec 02, 2010 | 2000 Ford Focus

2 Answers

2005 hyundai Accent, can't shift out of park and no brake lights


may want to check the brake pedal switch located on top of the brake pedal arm. If all fuses looks good, replace the brake pedal switch, which can also cause to not shift out of park.

Sep 24, 2009 | 2005 Hyundai Accent

Not finding what you are looking for?
Garden Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

john h

Level 3 Expert

12173 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...