How do i switch users - Computers & Internet

The possible causes are as follows:

The user name or password is incorrect.

Run the display local-user command to check whether the user exists.

Run the display local-user username user-name command to check whether the user password is correct.

There is no HTTP user access type.

Run the display local-user username user-name command to check whether the AuthMask field of the user contains H (HTTP login).

The user connected to the switch is full. The switch supports a maximum of five users.
LS S6720S 26Q EI 24S

In V100R006 and later versions, whenboth MFF and DHCP snooping are enabled, you can use the dhcp snooping user-bind autosave file-name command to back up DHCP snooping binding entries in a specified file. This configuration allows online users to retain online after the switch restarts. Note that the backup file saves only the first gateway address of users.
S5700 Switch Thunder link com

http://www.helpowl.com/p/D-Link/3350SR/Research/20945?search=des%203350sr%20setup

DES-3350SR Layer 3 Fast Ethernet Switch Users Guide reset Restrictions Only administrator-level users can issue this command. Example Usage:

To restore all of the switchs parameters to their default values: local>reset config Command: reset config Success. local> login Purpose Syntax Description Used to log in a user to the switchs console. login

This command is used to initiate the login procedure.

The user will be prompted for his Username and Password. none. none. Parameters Restrictions Example Usage: 46

hope this helps

Windows XP includes a new Microsoft Natural Keyboard shortcut to lock your computer. Any other compatible keyboard that includes the Windows logo key and the Application key can also perform this task.To use this shortcut, press the Windows logo key+L. The following list has different computer lock-up scenarios that are available to you, as well as other ways to lock the computer: Fast User Switching Enabled loadTOCNode(2, 'moreinformation'); If the Fast User Switching feature is enabled and you lock the computer, you can observe the same behavior as if you switched users: The computer returns to the Welcome screen and other users can log on to the computer. Fast User Switching Disabled loadTOCNode(2, 'moreinformation'); If the Fast User Switching feature is disabled and you lock the computer, the Unlock Computer dialog box is displayed that requires the current logged-on user to enter a password to unlock the computer.

Enable or Disable Fast User Switching Note: To enable Fast User Switching, you must also enable the Use the Welcome screen option. This feature cannot be used if your computer is a member of a domain. To enable Fast User Switching:

1. Log on to the computer as an administrator.
2. Click Start, click Control Panel, and then click User Accounts.
3. Click Change the way users log on or off.
4. If it is not already selected, click to select the Use the Welcome screen check box.
   
   NOTE: The Use Fast User Switching check box is unavailable until you click to select the Use the Welcome screen check box.
5. Click to select the Use Fast User Switching check box, and then click Apply Options. Quit the User Accounts tool.

Please don't forget to rate this solution.

Hi !

You may first check the selected options under Control Panel > User Accounts > Change the way users log on or off (the first option has to be selected so that user accounts are all shown on startup).

You can try to switch to that account using the start menu > Log Off > Switch Users after you have logged in to the admin profile.

hi check this link,maybe it will help you.

http://support.microsoft.com/kb/279765


Thanks

You forget the password for the "admin" user account and can no longer perform important management operations. Use the password recovery method outlined below to define a new password for the "admin" user account:

1. Access the Command Line Interface from the console port and enter the user name "recover" and password "recover" to place the Switch in password recovery mode. The Switch remains in password recovery mode for a maximum of 30 seconds, before it returns to the CLI login prompt.
   
   You must use the console port to recover the passsword. If you attempt the recovery method using the network, the password will be rejected.
   
   
2. Perform a hard reset on the Switch whilst it is in password recovery mode by switching it off, waiting a few seconds, and switching it on again.
   
   You cannot use a soft reset operation to reset the password of the "admin" user account. This will end the password recovery procedure and return you to the CLI login prompt.
   
   
3. When the Switch has rebooted following the hard reset enter a new password for the "admin" user account.
   

by switching user you have also switched configuration.the user that u have switched to has not been configured.it also may be disallowed.you can check and/or change this in admin.