Question about Mitsubishi Televison & Video

1 Answer

Mitsubishi hs-u62 vcr cassette will not eject

Cassette will partially eject, repeated pushing of Eject button will sometimes work, but usually not

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Needz fresh belts. You can order common o-ringz uv the same length that will work fine, but usually not az long.

Posted on May 12, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 579 Answers

SOURCE: Videocassette stuck in Panasonic NV-G50 VHS VCR; can't eject

Generally, you have to take off the cover, and find the motor that drives the cassette loading mechanism, then turn the motor shaft with your fingers (many many times) until the cassette is unloaded.
Usually the moter is easy to get at on top just to the right of the cassette mechanism. However sometimes it is underneath and you can only get at it by taking everything apart. Don't try this yourself and don't take the cassette carraige assembly apart trying to get at the cassette unless you don't plan on using this VCR again.

Posted on Dec 29, 2007

  • 579 Answers

SOURCE: vcr hs-u500

Typical belt drive failure. Take the cover off and turn the loading motor shaft with your fingers until the tape is ejected. Get a belt kit for this model and replace all the rubber parts in your VCR. Mitsubishi's are nice units and worth fixing. Check the little pulley under the capstan motor for cracks or worse.

Posted on Dec 31, 2007

sharcnet
  • 2130 Answers

SOURCE: Mitsubishi HS-U61 SVHS

When a tape won't eject, the problem can be caused by several things. The most common problem is that the belt that operates the eject mechanism is slipping and not allowing it to eject the tape. This can be fixed by either using a re-grip solution on the belt or have the belt replaced. Belts are inexpensive but sometimes difficult to get to. Most of the repair expense will be in the labor. Unplug the unit and take the cover off. Hopefully there will be enough clearance so you can get to the tape. Try to find the motor and belt that is responsible for operating the eject mechanism. The motor will look like a shiny cylinder, about the diameter of a quarter and will have a plastic pulley attched to the shaft. You can rotate the pulley and belt with your fingers and manually eject the tape. If the tape is around the spindles and video head, you will need to manually move the mechansim that retracts the spindles and returns the tape to the cartridge. While you may be successful in getting the tape out, you need to find out what caused the problem in the first place. Putting in another tape will most like become stuck again unless the problem is identified and resolved. Also look for a broken spring or cracked gear (missing teeth) in the eject mechanism. Please let me know if I can be of further assistance Good luck! - Jim

Posted on Feb 28, 2008

  • 8 Answers

SOURCE: flashing auto display - won't power up

The infra red light in the middle of the mechanical deck, that powers the left and right photo sensors is not ok.It looks like a small lamp( you cant see it when it works-Infra red mind it).The video cassette has a large round opening in the bottom towords the front, and accomodates this lamp.please check it out.

Posted on Apr 28, 2008

  • 2 Answers

SOURCE: VCR continually tries to eject the tape after it is inserted

If you have cleaned the head with a good head cleaner and you are still having a problem...the belt is probably worn. A good head clean should fix the problem.

Posted on Mar 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Got a mitsub Hs-u430 vcr.Pluged in & immediately starts eject.Does twice then stop.Only halfway eject.Does with no tape in.Took cover off & help tape in.Push any button it does same all over.


Disc loading mechanism fault. Contact any service technician. The mechanism should be taken out from the set, for repair. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

Oct 26, 2016 | Televison & Video

1 Answer

Will not eject tape


take the top off the VCR, you will see where the tape is hung up. Reach down and release the tape and pick it up, now close the top.

Jul 31, 2012 | Mitsubishi HS-U575 VCR

1 Answer

E-2 error what does that mean


E2 means: Loading motor locked in the unload direction. Usually(not always) happens with a going bad VCR tape on the rewind. Tape is becoming too difficult to rewind and/or VCR is getting tired. Eject tape. Discard tape as soon as practical, new tapes are cheap. To clear: Hold power on/off button for 8 seconds.

May 09, 2011 | Mitsubishi HS-U575 VCR

1 Answer

I have a Mitsubishi U57 VCR. Works well but have a tape stuck in it. Any suggestions on how to get it out?


Unplug the vcr for 30 seconds, sometimes the tape will eject, failing that ! remove the top cover of the vcr "2 to 6" screws. Now! if the tape is spewed in the mechanical parts and wrapped around the video ahead, get a pair of scissors and carefully cut away the tape and remove any particles, next hit the eject this should remove the cassette without difficulty. If all this fails the problem lies in the vcr itself, a bad idler assembly, broken drive belt, or loading basket problem which will require a technician.

Feb 19, 2011 | Mitsubishi Televison & Video

1 Answer

VHS Cassette stuck will not eject


take the cover off. try to locate the loading motor and turn the gear on it and the tape will slowly eject.

Jun 29, 2010 | Mitsubishi HS-U260 VHS VCR

1 Answer

The VCR doesn't eject the tape


need codes for vc-aa350 is locked

Sep 01, 2009 | Sharp VC-A560U VHS VCR

1 Answer

Plays for 3 secs, stops, and then ejects


This unit needs to have the "idler" changed as well as the belts. Over time, the internal rubber parts get hard ans slippery. There are safety checks inside that will stop the unit when problems are detected. With a slipppery idler assembly, the tape does not get wound into the cassette after passing the heads. Rather than have the tape collect inside and be destroyed, the unit stops. This is a relatively simple repair that any shop should be able to perform. Expect a parts cost in the $35 range. In my opinion, this unit is worth the repair as it will continue to provide service to you for years to come. New replacement units tend to last only a year or two.

Dan

Dec 30, 2008 | Mitsubishi HS-U770 S-VHS VCR

2 Answers

Mitsubishi HS-U61 SVHS


When a tape won't eject, the problem can be caused by several things. The most common problem is that the belt that operates the eject mechanism is slipping and not allowing it to eject the tape. This can be fixed by either using a re-grip solution on the belt or have the belt replaced. Belts are inexpensive but sometimes difficult to get to. Most of the repair expense will be in the labor. Unplug the unit and take the cover off. Hopefully there will be enough clearance so you can get to the tape. Try to find the motor and belt that is responsible for operating the eject mechanism. The motor will look like a shiny cylinder, about the diameter of a quarter and will have a plastic pulley attched to the shaft. You can rotate the pulley and belt with your fingers and manually eject the tape. If the tape is around the spindles and video head, you will need to manually move the mechansim that retracts the spindles and returns the tape to the cartridge. While you may be successful in getting the tape out, you need to find out what caused the problem in the first place. Putting in another tape will most like become stuck again unless the problem is identified and resolved. Also look for a broken spring or cracked gear (missing teeth) in the eject mechanism. Please let me know if I can be of further assistance Good luck! - Jim

Feb 28, 2008 | Mitsubishi HS-U447 VHS VCR

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1210 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...